2011 Gt Coupe Rwd Leather Lifetime Warranty V8 Engine We Finance 21k Miles on 2040-cars

Auto blog

2020 Ford Explorer ST vs 2019 Dodge Durango SRT: How they compare on paper

For a few years now, the Dodge Durango SRT has been the sole three-row performance crossover from a non-luxury brand. That all changes now that the 2020 Ford Explorer ST is coming to market. Now we have two family crossovers with rear-drive-based platforms vying for buyers that demand practicality and power. As such, there's no better time to dig into their specs to see how they compare. We'll check out each crossover's horsepower, torque, space, capability and prices. The full specs are listed below, followed by some analysis afterward. We also compared the regular 2020 Explorer models to other crossovers in this segment, if if that's not enough, you can check out our car comparison tool. Performance The Explorer and Durango go about making power in very different ways. The Explorer goes the force-fed route with two turbos feeding a 3.0-liter V6, while the Durango's enormous 6.4-liter V8 produces power with air flow au natural. Of the two, the Durango has the greater output of 475 ponies and 470 pound-feet of torque, feeding the flames of everyone that lives by the phrase "There's no replacement for displacement." The Explorer is no slouch at 400 horsepower and 415 pound-feet of torque, though. Performance isn't purely based on power, though. Other factors play a role, such as weight, and in that regard, the Explorer is way ahead. At 4,701 pounds, it weighs a massive 809 pounds less than the portly Durango. This also means that both crossovers are very close in weight-to-power ratio, with the Explorer only slightly worse at 11.75 pounds per horsepower and the Durango at 11.6. Less weight will also play a roll in handling, and the Explorer is likely to feel sprightlier without so much mass to shift back and forth. Semi-related to handling are tire sizes. The Durango features 295-mm wide tires on 20-inch wheels. The Explorer has 255-mm wide tires on 20-inch wheels, but 21-inch wheels with 275-mm tires are available. So the Durango is working with more contact patch, but as we mentioned, it's carrying a lot more weight. 2020 Ford Explorer ST View 20 Photos Interior Space and Practicality Although the Durango SRT is the largest on the outside in every dimension, it loses out to Explorer repeatedly inside. The Ford has more headroom, leg room and shoulder room in nearly every row except the third-row where headroom comes up a bit short.

The next-generation wearable will be your car

This year's CES has had a heavy emphasis on the class of device known as the "wearable" – think about the Apple Watch, or Fitbit, if that's helpful. These devices usually piggyback off of a smartphone's hardware or some other data connection and utilize various onboard sensors and feedback devices to interact with the wearer. In the case of the Fitbit, it's health tracking through sensors that monitor your pulse and movement; for the Apple Watch and similar devices, it's all that and some more. Manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality. As evidenced by Volvo's newly announced tie-up with the Microsoft Band 2 fitness tracking wearable, car manufacturers are starting to explore how wearable devices will help drivers. The On Call app brings voice commands, spoken into the Band 2, into the mix. It'll allow you to pass an address from your smartphone's agenda right to your Volvo's nav system, or to preheat your car. Eventually, Volvo would like your car to learn things about your routines, and communicate back to you – or even, improvise to help you wake up earlier to avoid that traffic that might make you late. Do you need to buy a device, like the $249 Band 2, and always wear it to have these sorts of interactions with your car? Despite the emphasis on wearables, CES 2016 has also given us a glimmer of a vehicle future that cuts out the wearable middleman entirely. Take Audi's new Fit Driver project. The goal is to reduce driver stress levels, prevent driver fatigue, and provide a relaxing interior environment by adjusting cabin elements like seat massage, climate control, and even the interior lighting. While it focuses on a wearable device to monitor heart rate and skin temperature, the Audi itself will use on-board sensors to examine driving style and breathing rate as well as external conditions – the weather, traffic, that sort of thing. Could the seats measure skin temperature? Could the seatbelt measure heart rate? Seems like Audi might not need the wearable at all – the car's already doing most of the work. Whether there's a device on a driver's wrist or not, manufacturers seem to be developing a consensus that vehicles should be taking on some of a wearable's functionality.

Michigan Gov. Gretchen Whitmer says manufacturing can reopen May 11

Michigan Governor Gretchen Whitmer on Thursday said the state's factories can reopen next Monday, May 11, removing one of the last major obstacles to North American automakers bringing thousands of laid-off employees back to work amid the coronavirus pandemic. While reopening the manufacturing sector, Whitmer also extended her state's stay-at-home order by about two weeks to May 28, citing a desire to avoid a second wave of COVID-19, the respiratory illness caused by the novel coronavirus. “WeÂ’re not out of the woods yet, but this is an important step forward," Whitmer said in a statement. "As we continue to phase in sectors of our economy, I will keep working around the clock to ensure our businesses adopt best practices to protect workers." This week, General Motors and Fiat Chrysler Automobiles said they were targeting resuming vehicle production in North America on May 18, but suppliers would need time to prepare ahead for that date. Ford has not said what date it is targeting. The governor previously extended the state's coronavirus stay-at-home order through May 15, but had lifted restrictions for some businesses. Neighboring Ohio had allowed manufacturing to resume this past Monday, putting pressure on Whitmer to follow suit. Michigan's shutdown had stymied efforts by the Detroit Three and rival automakers to restart vehicle assembly anywhere in the United States, because so many critical parts suppliers are based in the state. Automakers and their suppliers already have begun gearing up for a possible resumption of work at their U.S. plants, but needed the official go-ahead from Whitmer. Industry officials had been pressing Whitmer to allow suppliers to reopen starting May 11 so the automakers could resume operations on their target date. They also wanted the green light so they can press Mexico to open its auto sector as suppliers there are also critical for the industry restart. The automakers' plans were tacitly approved on Tuesday by the United Auto Workers union, which represents the Detroit automakers' hourly U.S. plant workers. The union had previously said early May was "too soon and too risky" to restart manufacturing. Under Whitmer's new order, factories must adopt measures to protect workers, including daily entry screening, no-touch temperature screening as soon as possible and use of protective gear like face masks. Automakers have already rolled out such policies.