St Manual 2.0l High Performance One Owner Excellent Condition Warranty Clean on 2040-cars

Auto blog

Ford issues six recalls covering 101,000 vehicles for multiple issues

Ford is announcing six separate recalls for a variety of issues affecting a dozen models and a total of 100,610 vehicles in North America. However, according to Ford spokesperson Kelli Felker, "None of them have caused accidents or injuries." Half of them cover fewer than 1,000 cars.
The largest recall covers 92,022 North American examples (about 83,250 in the US) of some models of the Ford Taurus, Lincoln MKS, Ford Interceptor, Flex and Lincoln MKT from the 2013 and 2014 model years; the 2012-2014 Edge and the 2014 Lincoln MKX. All of them have a potential issue with the halfshaft on the right side that might not be fully seated and could move outward over time. If it shifts too far, the models may no longer be able to drive, and the condition could also allow the vehicles to roll away, even when in Park. Dealers will inspect the shaft to make sure it's seated and will replace the part if necessary.
The next-largest recall covers 5,264 North American examples (4,867 in the US) of the Ford F59 Commercial Stripped Chassis from the 2011-2014 model years. It's possible that an electrical junction box can corrode in areas with salty roads and short circuit. The problem could potentially cause a fire. Dealers will replace the box with an improved design.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.

Creations n' Chrome Top Notch Mustang is a one-of-a-kind fox

Is there a cooler car from the 1980s and early 90s to mod than a Fox-body Ford Mustang? No, there isn't. If you disagree with us, we suggest you have a look at this 1990 Mustang Coupe, which just might change your mind. Although considering just how extensively modified this car - the Top Notch Mustang from Creations n' Chrome - is, we wonder just how much Ford is left in this old pony.
It rides on a custom race tube chassis that weighs a scant 700 pounds, while carbon-fiber bits and bobs help lower the overall curb weight to a mere 2,400 pounds. When paired with supercharged, 5.0-liter, Aluminator V8 from Ford Racing, the results are, doubtlessly, exciting. 855 horsepower at the rear wheels and 667 pound-feet of torque are available from that force-fed V8 should be just plenty for this car's intended purpose of running in standing-mile competitions.
The Top Notch Mustang is more extreme than just weight savings and a big engine, though. That 5.0-liter is essentially in what's known as a front-mid layout - where the engine is actually behind the front axle. In this case, the 5.0-liter V8 is 17 inches further back than a factory Fox-body, for better weight distribution. As a result, the cabin has been completely overhauled. An SLA front suspension, wheels from HRE, Wilwood brakes and Sparco interior items round out the extensive list of mods.