2011 Ford F350 Lariat on 2040-cars

Auto blog

Ford issues six recalls covering 101,000 vehicles for multiple issues

Ford is announcing six separate recalls for a variety of issues affecting a dozen models and a total of 100,610 vehicles in North America. However, according to Ford spokesperson Kelli Felker, "None of them have caused accidents or injuries." Half of them cover fewer than 1,000 cars.
The largest recall covers 92,022 North American examples (about 83,250 in the US) of some models of the Ford Taurus, Lincoln MKS, Ford Interceptor, Flex and Lincoln MKT from the 2013 and 2014 model years; the 2012-2014 Edge and the 2014 Lincoln MKX. All of them have a potential issue with the halfshaft on the right side that might not be fully seated and could move outward over time. If it shifts too far, the models may no longer be able to drive, and the condition could also allow the vehicles to roll away, even when in Park. Dealers will inspect the shaft to make sure it's seated and will replace the part if necessary.
The next-largest recall covers 5,264 North American examples (4,867 in the US) of the Ford F59 Commercial Stripped Chassis from the 2011-2014 model years. It's possible that an electrical junction box can corrode in areas with salty roads and short circuit. The problem could potentially cause a fire. Dealers will replace the box with an improved design.

Autoblog Video: Looking back on the 1965 Shelby GT350

The first Shelby GT350 Mustang came out a year after the first Ford Mustang, a collaboration between the carmaker and Carroll Shelby bent on making the Mustang a race winner. Perhaps even better than the car is Shelby's story behind its creation, when Ford chairman Lee Iaccoca gave him the "impossible job" of turning "a secretary's car... into a sports car." Shelby and his cohorts got that job done immediately, taking three SCCA B-Class national championships. The latest Ford Shelby GT350 is coming a year after the latest Mustang's debut, and it's certainly got the specs on paper to look like a track monster, especially in GT350R form. This year the Rolex Monterey Motorsports Reunion celebrated the 50th anniversary of the Shelby GT350 Mustang, and the Pebble Beach Concours D'Elegance featured the car in a special category. We took the opportunity to look at what makes the old GT350 so special, and why the new one stays true to the legendary name. Check it out in the video above. Related Video:

Shelby GT350R offers first mass-produced carbon fiber wheels

In the world of race engineering, reducing total weight is good, but reducing unsprung weight is flippin' fantastic. That's the reason Ford is pushing the envelope in terms of technology for the Shelby GT350R's wheels. Joining the likes of Koenigsegg in the offering, Ford has teamed with Australian outfit Carbon Revolution to produce the CF rollers en masse for the first time. Destined for the hubs of the new Shelby GT350R, the new hoops weigh just 18 pounds each, versus the 33-lbs weight of a similar aluminum wheel. On top of slashing up to 60 pounds in unsprung weight, there's such a reduction in rotational inertia – 40 percent, versus aluminum wheels – that Ford actually has to recalibrate the magnetic ride control system and springs. Thanks to, we're guessing, scenes of crashed Formula One cars disintegrating and spewing shards of carbon fiber all over the track, Ford seems quite keen to do away with the idea that CF is strong, but brittle. The company conducted extensive shock testing, ramming a wheel into a curb at speed. According to the Blue Oval, the lightweight wheel allowed the suspension to respond so quickly that the impact was "greatly diminished," causing the tester to run the experiment again, thinking there'd been a mistake. After recording brake rotor temperatures of 900 degrees Celsius (over 1,650 degrees Fahrenheit, or well past the point that aluminum or magnesium would melt) during testing, Ford and Carbon Revolution actually redesigned the wheels to "a thermal standard more suitable for motorsports," by adding an "incredibly thin, nearly diamond-hard coating that reliably shields the resin from heat." The same process was used to protect engine turbine blades on the Space Shuttle. While the work by Ford and Carbon Revolution should make GT350R customers excited, the work being done here could have serious implications for performance cars in the future. That's the real takeaway here, and is something that should leave fans of all performance vehicles excited.