1997 Ford F-350 Xl Reg. Cab Drw 2wd- 9 Ft Dump Bed ~ Sos At Odot In Salem, Or on 2040-cars

Auto blog

Shelby GT500 and Roush Stage 3 go head to head at the drag strip

The Ford Mustang is a brilliantly affordable source of horsepower, with a base 300-plus-horsepower version available for well under $30,000. Jumping up to about $35,000 will get you a solid 420 horsepower from a high-revving V8, while those with some extra disposable income can get a pair of 600-plus-horsepower monsters. Both the Roush Stage 3 with its Phase 3 package and Ford's factory Shelby GT500 even crest the 650-horsepower mark, with 675 and 662 ponies, respectively.
Naturally, someone needed to find out which of these hi-po Mustangs was the quickest. And while this video is quite obviously a dealership commercial, at least there's some solid drag racing between two of the most powerful performance machines available for under $100,000.
With two NHRA drag racers at the wheel, the Stage 3 and GT500 go head to head for three races. Scroll down below to see the results in the full video.

Jurassic Park made a big impact on these Jeep drivers

For a certain cohort of young folks, Jurassic Park is a touchstone film from their childhood. Not only did it play into practically every little boy's love of dinosaurs, the movie included some great action scenes and special effects that still hold up today. In its latest video, The Aficionauto takes a look the Jurassic Park Motor Pool, a California car club with over 40 fans who created replica vehicles from the iconic film.
The club is made up of an interesting cross-section of people. Many of them were Jeep Wrangler fans that already loved off-roading and Jurassic Park, and liked the idea of bringing them together. Like any close-knit club, it ends up being about community and people coming together to share their interests. It's quite a heartwarming video. Also, be sure to stay until the end because The Aficionauto teases a future Jurassic Park-themed vehicle. Scroll down to check out the motor pool.

All eyes on Detroit as automakers prepare for slow, careful reopening of plants

DETROIT — The U.S. factories that make Fords, Chevys and Jeeps are coming back to life this week as workers install new safety equipment and wake up machines ahead of the high-stakes restart the Detroit automakers plan to launch on Monday. Ford, General Motors and Fiat Chrysler Automobiles all plan to reopen North American factories on May 18. The reopening of the U.S. auto sector will be a closely watched test of whether workers across a range of industries can return to factories in large numbers without a resurgence of COVID-19 infections. How well the automakers do will be significant for the U.S. economy, as nearly 1 million workers are employed in the sector. Executives at Ford and GM said separately this week the companies have not recorded any cases of COVID-19 transmission in plants outside the United States since adopting new safety protocols. Those procedures include mandatory face masks, separation of workers on assembly lines, frequent cleaning of work areas and requirements that workers pass through temperature monitors and report any symptoms before entering a plant. The Detroit Three have taken unprecedented steps to share information about coronavirus safety practices and develop a common set of workplace standards for their restarts, working with the United Auto Workers union, executives said. "We thought it was critical that we did it together," Ford manufacturing and labor chief Gary Johnson told Reuters. "We've never done this as an industry." The Detroit automakers will restart U.S. plants without regular testing of workers, because they do not have access to sufficient testing capacity, executives and UAW officials said. They will test workers who report COVID-19 symptoms or have fevers discovered by temperature scanners installed at factory entrances. "We have to continue to push for this testing," United Auto Workers union Vice President Cindy Estrada told Reuters on Wednesday. "Unless we have testing weekly to keep sick people out of the plant there is always a risk." Adopting new safety practices is just part of the work the companies must do to reopen after an extraordinary shutdown that has lasted two months.   Wave zero At Ford, workers going in to ready factories are part of what Chief Operating Officer Jim Farley calls "wave zero." The work of wave zero employees "is really important for success of the startup," he said in an interview.