1996 Ford F-350 Xl on 2040-cars

Auto blog

Focus STs for SEMA include Lotus and Gulf liveries, rally-fied police car

Ford, as we mentioned on Saturday, is pulling out all the stops for November's SEMA show, bringing 57 vehicles to the Las Vegas event. Ford will be staggering the release of its SEMA flotilla, though, so expect to hear a lot about the new additions to the fleet in the weeks to come. We already showed you the Fiesta, Fiesta ST and Mustang models that made up the first batch of SEMA cars. Next up, we have a quartet of modded Focus STs joining Ford's SEMA roster.
Our first Focus ST (pictured above) sports the legendary livery of Gulf Racing. The orange-on-blue scheme, which Ford helped make famous at the 24 Hours of Le Mans, has been updated for 2013, with a more vibrant blue. This ST was built by Universal Technical Institute, while the exterior was done by Neil Tjin of Tjin Edition. Side exhausts, a Vortech supercharger and a Motiv Concepts high-flow cat allow the ST to breathe a bit easier, while Forgestar wheels contrast well with the iconic paint scheme.
Focus ST number two has been done-up by PM Lifestyle and is inspired by "Southern California car culture." Sporting a sleek, pale blue paint job, there's also no shortage of carbon fiber on the car's exterior. The 2.0-liter, turbocharged, four-cylinder engine has been massaged by the likes of Banks Power, COBB Tuning and Ford Racing, while the suspension is wearing a shiny, new set of coilovers and sway bars. The meaty brakes, tucked behind 19-inch, Rotiform wheels, come from Wilwood, while the cabin has been fitted with a pair of Sparco Chrono seats and five-point, Schroth harnesses.

Second-tier UAW workers promoted for first time after Ford hits quota

The United Auto Workers put out a statement on Friday that 55 Ford workers chosen by seniority would be moved from the Tier 2, entry-level pay rate of around $19 per hour to the Tier 1, non-entry-level rate of about $28 per hour. One of the stipulations in the 2011 UAW-Ford agreement was that only 20-percent of the total hourly workforce could be paid the Tier 2 wages agreed upon in 2007; after that, those workers had to be moved to Tier 1. Even so, the new Tier 1 status makes them less expensive to Ford than veteran Tier 1 workers because they receive fewer benefits. However, Automotive News had reported that same day that Ford was 69 workers shy of the limit, and when AN asked Ford about the situation Ford said it had "some room" on the entry-level roster. If workers do move to the higher pay grade, it will be the first time that's happened since the two-tier system was agreed. But it sounds like there's going to be some haggling between the UAW and Ford before that happens. Ford is the only one of the Detroit 3 automakers to have to work with a cap, since it didn't go through bankruptcy proceedings during The Great Recession; General Motors and Chrysler jettisoned the cap in 2009. GM is said to have 16 percent of its hourly workers at Tier 2 while Chrysler has 42 percent, but Fiat-Chrysler CEO Sergio Marchionne has long been opposed to the two-wage system. The UAW is preparing for its 2015 negotiations with the US automakers. It wants to eliminate the difference in pay by going to the higher scale, if there is a consensus among automakers it seems to be that they also want a single wage, but less than the higher scale, with the addition of profit-based bonuses. The recent statement from the labor union is below. UAW President Dennis Williams and UAW-Ford Vice President Jimmy Settles announced today that the union is delivering on its promise to convert workers DETROIT, Jan. 30, 2015 /PRNewswire/ -- UAW President Dennis Williams and UAW-Ford Vice President Jimmy Settles announced today that the union is delivering on its promise to convert workers making entry-level wages to traditional employees. "The 2011 UAW-Ford agreement allows for a contractual limit of entry-level employees. Once that threshold is surpassed, entry-level employees convert by seniority to 'regular, non-entry level employment.' At this time, fifty-five UAW-Ford workers will receive the wage increases, which put them in the category of non entry-level employment.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.