2011 Ford F250 Super Duty on 2040-cars

Auto blog

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.

Ken Block walks you through his new 'Hoonigan Racing' HQ

Ken Block seems like one hell of a nice guy. I ran into him at CES this past January, and he dropped the video games he was playing to chat with me for a while. His crew also recently gave our Steve Ewing a tour of the offices you're about to see on this video. Good guy to know.
As it turns out, they're some fairly cool new digs. Dubbed 'Hoonigan Racing Division HQ,' the office is open to Ford Focus ST and Fiesta ST owners who attend the driving program offered out at Miller Motorsports Park. The very same program that Ewing reported on just recently.
Or, if you've no plans to buy an ST or travel to Utah any time soon, you can let Block show you around himself in this MTV Cribs-style video. With interior decorating that relies heavily on shipping containers and luxurious amenities like a ping pong table, 10 refrigerators and a bear(?), there's no lack of eye-candy in the driverly HQ. (Judging by Block's outfit, you'll probably not go thirsty if you're a Monster drinker, either.) Take the tour along with the Gymkhana master, below.

2017 Ford F-150 Raptor desert testing heats up

In case there was any doubt, Ford is taking the development of the second-generation SVT Raptor very, very seriously. The Blue Oval recently completed over 1,000 miles of testing in the boiling heat of the American southwest. Apparently, that mileage was accrued over a 66-mile route designed to mimic the torturous terrain encountered by racers in the Baja 1,000 off-road race. The prototypes, which were built from a mix of existing and next-gen Raptor components, were tested with "fast sandy washes, deep-rutted silt beds, steep climbs in deep sand, and slow meticulous crawls through tight trenches." Ford claims the new truck managed to run the circuit 25-percent faster than the current F-150 SVT Raptor, averaging 50 miles per hour while going as fast as 100 mph in stretches. That said, Dearborn didn't release any dedicated times, so it's unclear just how quickly the 66-mile stage was completed. We do know that durability was a big part of the testing. Ford claims each lap was completed by what sounds like a pretty significant jump, with the trucks ascending a steep ramp onto a two-foot plateau and then completing a step-down to level ground. We have to take Ford at its word here, though. "Steep" can mean any number of things, and we've no idea just how fast the trucks were hitting the ramp or how much air they got. Hopefully, the jumps were aggressive enough to prevent future frame issues. Still, Ford boasting about how rough the Raptor's testing is can be taken as a positive sign for fans of the next-generation of SVT's rugged pickup. NEW F-150 RAPTOR WRAPS UP INITIAL DESERT DURABILITY TESTING DEARBORN, Mich., July 7, 2015 – The 2017 F-150 Raptor – Ford's toughest, smartest, most capable off-road truck ever – recently completed more than 1,000 miles of testing in the southwestern United States. Over 1,028 miles of desert trail designed to parallel the Baja race course in Mexico, the 66-mile route featured a wide range of surfaces including fast sandy washes, deep-rutted silt beds, steep climbs in deep sand, and slow meticulous crawls through tight trenches. The truck topped speeds of 100 mph in places, slowing to 10 mph in others, for an average speed of approximately 50 mph. The 2017 Raptor is 25 percent faster than the current truck based on lap times. At the end of each lap, the new Raptor completed a tabletop jump consisting of a steep ramp up to a two-foot plateau, then a step-off back to level ground.