02 F250 (7.3) Diesel Short-bed Programmer+ Afe Intake (carfax) 4wd Ranch-hand Tx on 2040-cars

Auto blog

Ford Q1 profits dragged down by warranty costs

General Motors isn't the only Detroit automaker posting falling profits in the first quarter. Ford just released its Q1 2014 financial data, and it reported a net income of $989 million, down $622 million from Q1 2013. The drop is partially blamed on higher warranty and recall expenses than the company had anticipated.
Financially, Ford suffered a rough quarter almost across the board. Its pre-tax profit of $1.4 billion was also down $765 million from a year ago. Things were even worse in the North American market where operating profit fell significantly to $1.5 billion, down from $2.392 billion in Q1 2013. However, its global revenue ticked up slightly to $35.9 billion, from $35.6 billion in this period in 2013.
Ford admitted that it spent about $900 million on expenses that it hadn't planned for during this quarter. According to Reuters, the company paid about $400 million in additional warranty and recall costs in North America. The automaker didn't explain why the costs were so much higher than expected. However, in the last three months, Ford has had several recalls, including on the 2001-2004 Escape for rust, Explorer for its steering, Edge for its fuel line and others.

Want a V8 on the cheap? Buy a work truck

In case you didn't notice, V8 cars have gotten pretty expensive. If you want a modern muscle car like the Dodge Challenger R/T, Ford Mustang GT, or Chevy Camaro SS, you'll need between $34,000 and $38,000 for a stripped out example of one. The cheapest of those is the Challenger, and the priciest is the Camaro. These are also the cheapest V8 cars the companies offer. But if you absolutely have to have a V8 for less, there is an option, work trucks. As it turns out, all of the Big Three offer their most basic work trucks with V8s. And because they're so basic, they're pretty affordable, especially when sticking with the standard two-wheel drive. A Ram 1500 Tradesman with a V8 can be had for as little as $29,840, which is a little more than $4,000 less than a Challenger R/T. For a bit more at $30,275, you can have a Chevy Silverado W/T, almost $8,000 less than a Camaro SS. The most expensive is the V8 Ford F-150 starts at a starting price of $30,670, which is a bit over $5,000 less than the Mustang. Of course you'll be in an ultra bare bones vehicle with few comforts, and the price will go up if you add stuff, but we're bargain hunting here, and sacrifices are sometimes necessary. Besides, what you lose in comfort, you gain in loads of cargo space and towing (try to look at the bright side). Also, as a side note, all three trucks are available with optional electronic locking rear differentials. At the discounted price of these trucks, you still get a heaping helping of power. The most potent of the trio is the Ram 1500 Tradesman with 395 horsepower and 410 pound-feet of torque generated by a 5.7-liter V8. Compared with the Challenger R/T, the Ram is up by 20 horsepower and they're tied for torque. The value proposition is even more stark between the two vehicles when looking at the price per horsepower. Each pony in the Ram costs $75.54, while the Challenger charges you $90.91. The Challenger is also more expensive per horsepower than its close competitors. The F-150's 5.0-liter V8 is just barely behind the Ram with 395 horsepower and 400 pound-feet of torque. That's still more power than the Challenger, and it matches the torque of the 2017 Mustang GT. On the down side, it still would be down 20 horsepower on that same 2017 Mustang, and it's behind by 60 horsepower and 20 pound-feet on the new 2018 Mustang GT. The F-150 also just edges out the Mustang in the dollar per horsepower measure.

William Clay Ford Sr. dead at 88

William Clay Ford, retired vice chairman of Ford Motor Company and the last surviving grandchild of company founder Henry Ford, died this morning after a bout with pneumonia. He was 88.
Ford spent 57 years with his grandfather's company, joining the board of directors in 1948 before graduating from college. Ford also held a position as chairman of the design committee, as well as the chairman of the executive committee and vice chairman of the Board of Directors during his tenure with the company. In a 2013 Detroit Free Press story, retired CFO Allan Gilmour said Ford had an eye for design, and was once able to pick out when a fiberglass model of a Ford Contour was asymmetrical, off by an inch on one side. He retired and assumed the position of director emeritus in 2005.
"My father was a great business leader and humanitarian who dedicated his life to the company and the community," said Bill Ford, Jr., Ford's current executive chairman. "He also was a wonderful family man, a loving husband, father, grandfather and great-grandfather. He will be greatly missed by everyone who knew him, yet he will continue to inspire us all."