Limited 7.3l Diesel! 4wd Nicely Equipped! Runs Great! Must See! on 2040-cars

Auto blog

Dealers price gouging Ford Mustang 50th Anniversary Edition by up to $20k [UPDATE]

UPDATE: Sheehy Ford's Cory Belcher got back to us, confirming that the price premium was related to the limited nature of the 50th Anniversary Mustang and that the figure listed was based on what other dealers were charging, while adding that the dealership was "very flexible" on the final price of the special edition car. So while there remains a hefty markup, it's possible that consumers could get out the door without spending quite so much over MSRP. It's no secret that dealers take some – let's call them "liberties" – with the prices on vehicles that are very new, highly in demand or available in very limited numbers. As we've explained before, they're well within their rights to charge so-called market value adjustments. We don't usually see these adjustments on mainstream vehicles, though. Then again, you could argue that the 2015 Ford Mustang 50th Anniversary Edition is not necessarily a mainstream vehicle. It starts at $46,170, which isn't peanuts, but it's still a Mustang. There's still a large portion of the buying public that could put one in their driveway, if they so chose. Then again, maybe they can't. That's because dealers are (still) issuing massive premiums on top of MSRP for the limited-edition model. It's happening at Sheehy Ford Gaithersburg, where a salesperson named Lou confirmed to Autoblog that the dealership is charging around $20,000 over MSRP on not one, but two Anniversary Editions. He explained that Sheehy isn't alone in the upcharge: "We like to see what other dealers are asking for," he told us, in reference to the limited edition 'Stang. We have a message in for the dealership's general manager for deeper info, too, and will update this post when/if we hear back. We corroborated Lou's story, though, with another Maryland area dealer, Century Ford, who confirmed that the $46,995 listed on the dealer's website for its Wimbledon White Anniversary car was incorrect, and the actual price was "around $64,000." He echoed Lou's reasoning for the upcharge, while adding that dealers are likely only going to see one or two examples, of the 1,964 produced. Perhaps the most worrying part of this entire affair is the sense of deceit that accompanies it. Neither of the dealers we spoke to copped to the market value adjustments on their website. We had to call and ask specifically about the cars in question to get the actual price.

2016 Ford Focus RS may yet be AWD, US sales likely

When it comes to forbidden fruit, few vehicles are spoken of in as hushed a tone as the Ford Focus RS. The turbocharged, five-cylinder hot hatch could only be seen from afar by American customers as it tore up the roads of Europe. And while it's safe to say that Ford's Yankee fans are quite happy to now be on equal footing with drivers in the old country thanks to the Focus ST, we doubt there'd be much protestation over a successor to the RS arriving stateside.
Of course, we've seen images of the new RS undergoing testing, but a new story by Road and Track aims to fill in some very large blanks in our knowledge of that car, thanks to a pair of mysterious insiders at the Ford. Chief among those is this - the RS will almost certainly make its way to the US, albeit in limited quantities. It gets better, though.
Under hood, the new RS is unsurprisingly expected to borrow the 2.3-liter, turbocharged four-cylinder from the 2015 Ford Mustang and 2015 Lincoln MKC. While that twin-scroll turbo produces 310 horsepower in the Mustang and 285 ponies in the MKC, R&T expects the RS to deliver quite a bit more firepower - 325 to 350 hp, with preference going to the higher output due to the limited-edition nature of the RS. This roughly fits with previous reports.

Ford reveals new rapid prototyping and low-volume production techniques [w/video]

It's called "F3T," and that stands for Ford Free-form Fabrication Technology. The process that The Blue Oval has developed means being able to sidestep the weeks-long process of tool-and-die making when engineers want to construct a new part, allowing them to fabricate a three-dimensional part from a two-dimensional sheet of metal in just hours.
While F3T is being developed it is limited to "low-volume prototyping or even low-volume niche vehicles," but the next step is to evaluate it for use in Ford's global manufacturing facilities. You can find out more about it in the video and the press release below.