2004 Ford E150 High Top Conversion,texas Ranch Edition,dvd,playstation on 2040-cars

Auto blog

Ford recalls 1.48 million F-150s for transmission, plus other models

Weeks after recalling more than 800,000 F-Series pickup trucks for a fire risk, Ford has issued another separate recall for approximately 1.48 million 2011-2013 F-150s for a transmission fault. The six-speed automatics could unexpectedly downshift into first gear without warning. Ford and Lincoln tangentially issued much smaller recalls for the Mustang, Continental, Nautilus, and Navigator. According to Ford, some 2011-2013 model year F-150 pickups with six-speed automatic transmissions could "experience an intermittent loss of the transmission output speed sensor signal to the powertrain control module." This could potentially cause the trucks to temporarily downshift, which could be dangerous if it occurs while driving. Of the 1.48 million affected trucks, 1.26 million are in the U.S. while 221,000 are in Canada. Thus far, Ford knows of five reported accidents involving the issue. To remedy the problem, owners can take their trucks to dealers to update the power control module software. Ford also issued recalls for about 4,350 2019 Mustangs, Lincoln Nautiluses, and Lincoln Navigators in the U.S. and Canada due to a possible fault with the instrument clusters. Although there have been no reports of accidents, Ford says the instrument panel clusters assemblies might be blank or not turn out when the vehicle is started. Additionally, Ford issued a third recall for 28,200 2017-2019 Lincoln Continentals in the U.S. and Canada. Ford says silicon contamination might build up inside the door latch motor, causing it to malfunction. As a result, the door latch might not always fully engage, and the doors could possibly open unexpectedly. Despite no reports of accidents, Ford will remove and replace door latch assemblies on all doors for those affected by the defect. If any of these apply to a vehicle you own, contact Ford to discuss whether it is included in any of these recalls and have the vehicle checked out at a Ford dealership.

Shelby GT350R offers first mass-produced carbon fiber wheels

In the world of race engineering, reducing total weight is good, but reducing unsprung weight is flippin' fantastic. That's the reason Ford is pushing the envelope in terms of technology for the Shelby GT350R's wheels. Joining the likes of Koenigsegg in the offering, Ford has teamed with Australian outfit Carbon Revolution to produce the CF rollers en masse for the first time. Destined for the hubs of the new Shelby GT350R, the new hoops weigh just 18 pounds each, versus the 33-lbs weight of a similar aluminum wheel. On top of slashing up to 60 pounds in unsprung weight, there's such a reduction in rotational inertia – 40 percent, versus aluminum wheels – that Ford actually has to recalibrate the magnetic ride control system and springs. Thanks to, we're guessing, scenes of crashed Formula One cars disintegrating and spewing shards of carbon fiber all over the track, Ford seems quite keen to do away with the idea that CF is strong, but brittle. The company conducted extensive shock testing, ramming a wheel into a curb at speed. According to the Blue Oval, the lightweight wheel allowed the suspension to respond so quickly that the impact was "greatly diminished," causing the tester to run the experiment again, thinking there'd been a mistake. After recording brake rotor temperatures of 900 degrees Celsius (over 1,650 degrees Fahrenheit, or well past the point that aluminum or magnesium would melt) during testing, Ford and Carbon Revolution actually redesigned the wheels to "a thermal standard more suitable for motorsports," by adding an "incredibly thin, nearly diamond-hard coating that reliably shields the resin from heat." The same process was used to protect engine turbine blades on the Space Shuttle. While the work by Ford and Carbon Revolution should make GT350R customers excited, the work being done here could have serious implications for performance cars in the future. That's the real takeaway here, and is something that should leave fans of all performance vehicles excited.

Ford will add lots of carbon fiber to new vehicles

With BMW receiving a bunch of positive press for its usage of carbon fiber to build its i3 and i8 plug-in vehicles, Ford is jumping into that game as well. The US automaker has reached a manufacturing agreement with Dow Chemical to speed up the use of that material in Blue Oval vehicles. Carbon fiber usage will cut weight from Ford's new products, boosting fuel efficiency as a result. Ford will work with DowAksa, a 50/50 joint venture between Dow Chemical and Turkey-based Aksa Akrilik Kimya Sanayii A.S, on a manufacturing partnership. The goal is to speed up technology research to make it cheaper to make cars and trucks with carbon fiber materials. Ford's light-weighting efforts received a boost of sorts this week when its aluminum-body 2015 F-150 was awarded a five-star Overall Vehicle Score in the National Highway Traffic Safety Administration's testing, making this year's version the safest to date. The new body construction cut 700 pounds from the truck's curb weight. Take a look at Ford's press release about DowAksa below. FORD, DOWAKSA TO JOINTLY DEVELOP CARBON FIBER FOR HIGH-VOLUME AUTOMOTIVE LIGHT-WEIGHTING APPLICATIONS Ford and DowAksa formalize agreement to advance the adoption of cost-effective carbon fiber components through technology validation and proof of concept to reduce vehicle weight and increase fuel efficiency without sacrificing strength Agreement provides pathway for a high-volume manufacturing partnership New joint development agreement accelerates joint research announced in January in partnership under new U.S. composites manufacturing institute Ford and DowAksa today signed a joint development agreement (JDA) to formally advance research on cost-effective, high-volume manufacturing of automotive-grade carbon fiber, a material poised to play a significant role in the drive to make vehicles lighter for greater fuel efficiency, performance and capability. The agreement, between Ford Motor Company, Ford Global Technologies and DowAksa – a 50/50 joint venture between The Dow Chemical Company and Aksa Akrilik Kimya Sanayii A.S – will combine DowAksa's feedstock capacity, carbon fiber conversion and downstream intermediates production capabilities with Ford's expertise in design, engineering and high-volume manufacturing. The goal is to produce materials that make cost-effective carbon fiber composite parts that are much lighter than steel but meet automotive strength requirements.