1923 Ford Model T Bucket on 2040-cars

Auto blog

Ford brings FPV Falcon production in house [w/video]

For the first time since 1976, Ford of Australia is bringing the assembly of its stonking Ford Performance Vehicle line back in-house to the company's Broadmeadows and Geelong facilities. That's a point of pride for FPV, which builds high-performance versions of the Australian Falcon model like the F6, GS and the heroic GT seen here.
In the video below, we hear FPV employees talking in hushed tones about the important legacy that cars like the GT have for Australian gearheads of all stripes, and how proud they are to say that hand-built machines like this GT R-Spec with its Boss 355 engine are now rolling out of their home base. For our part, we're just dying to drive this version of the Coyote V8; the engine is rocking a "Miami" supercharger from Harrop and makes some 450 horsepower.
Continue on below for the video, or you can check out some images of the new FPV at the facility, as well as a gallery of the GT R-Spec car.

A cool boost to turbocharger performance

Since the advent of the forced-induction engine, we have been looking for ways to get every drop of performance we can. There are many approaches to getting additional power using better intercooling, water injection, or even adding nitrous oxide. One take on a short instant burst of power is being researched by Mahle and involves providing supercooled air to an engine, which allows it to burn a leaner fuel mixture and produce more power. The supercooling idea is not new and was examined by Ford in 1993 on the Mustang Mach III concept car, then brought up again in 2003 with the SVT F-150 Lightning concept. Ford called its system the SuperCooler; it was designed to work with any turbocharged or supercharged engine equipped with a water-to-air intercooler. The system on the Lightning concept used a small tank of antifreeze that was hooked up to the truck air conditioning compressor. The air conditioning compressor cooled the antifreeze down to about 30 degrees. The other side of the tank was hooked up to the air-to-water intercooler, which usually had a temperature over 100 degrees. Once the antifreeze was circulated from the tank into the intercooler, it would lower the intercooler temperature and provide for a cooler, denser air charge into the engine; the result was around 50 extra horsepower for a burst of about 30 seconds to a minute, depending on the size of the tank. The system for the Lightning was to be offered as a $750 option and would have been targeted towards drag racers and the like, as it could be used for a run down the drag strip and then re-cooled by the time the truck was back in line. The system was fairly non-intrusive – it only weighed about 25 pounds and did not require a new compressor or intercooler. But as with many concepts, it was ultimately scrapped. The technology was always stuck in the back of my mind, but with larger and more powerful engines being produced it could not find its place. With the advent of new fuel economy standards, we have seen small-displacement turbocharged engines pop up and they seem like the perfect candidate for this type of technology. Ford's EcoBoost 1.0-liter three-cylinder turbocharged engine, as used in the Fiesta and Focus, is one such candidate for this technology. It would add a negligent amount of weight but could provide a boost of 10 to 20 horsepower when needed, like merging onto the highway or catching up to traffic.

Airbag recall widens to include BMW, Chrysler, Ford and Toyota

The recall of faulty airbag inflators supplied by Takata has exploded today to grow to seven automakers. In most cases, only models in certain high-humidity regions were affected because the National Highway Traffic Safety Administration found in its investigation that moisture played a roll in determining whether there would be a problem. However, some companies opted for national campaigns. The exact number of affected models for these campaigns isn't yet known at this time.
BMW is recalling an undisclosed number of 325i, 325Xi, 330i and 330Xi models from the 2001 through 2005 model years and the 2001-2006 model year versions of the 325Ci and 330Ci for the driver side and passenger side inflators. Only vehicles currently registered in Florida, Puerto Rico, Hawaii and the US Virgin Islands are covered under this recall.
Neither Chrysler's filing with NHTSA nor its press release list the specific models affected, but a company spokesperson told Autoblog that at this time it only covers the driver and passenger side inflators for the 2006 Dodge Charger in Florida, Puerto Rico, Hawaii and the US Virgin Islands