1999 Ford F350 Crew Cab, Dually, 7.3l Powerstroke Diesel, Auto, Very Clean! on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

How Ford switched gears for the all-new F-150

Editor's Note: This story is authored by Julia Halewicz, a senior editor with AOL's Custom Solutions Group. She holds a Masters in Journalism from NYU and has spent her career as an editor of various newspapers, magazines and digital outlets. Last year on the Friday before Labor Day, the 2014 Ford F-150 pickup truck came off the Dearborn assembly line for the last time. After the last seam was welded, the F-150 that had been so beloved by American consumers would begin the transition from traditional steel manufacturing to an aluminum body, and the second phase of Ford's 2007 blueprint for sustainability would begin. Jobs would be created, and Ford would deliver a stronger product to its consumers. It was a moment Ford would call the biggest in the company's 111-year history. Breaking The Mold For some, the change was almost unfathomable. How could a truck be made with aluminum, and why change what clearly was working very well for the company? "We have a saying at Ford that leaders lead," said Doug Scott, the company's truck group marketing manager. "This was an ideal product to make with aluminum-alloy, because lightweighting made so much sense for a truck, because the extent to which you could take weight out of a truck, you could add more value to the customer in terms of more towing, more payload, more durability, more efficiency – so again all this required us to be out in front further out in front that we normally would be to make sure that we would deliver on all those expectations." Ford began the planning process about five years before the first aluminum F-150 would come to market. The company had a lot of questions. What was customer acceptance of aluminum, could they build the truck, and could the truck be repaired out in the field? Finally, Ford needed to determine if there were enough materials available to support the demand for the F-Series. Aluminum vehicles aren't unusual, but had never been built on the scale of the F-150 – approximately one every minute. Ford created two prototypes to determine if the product would meet and exceed consumer expectations. Any change to the vehicle had to be justified in performance, safety and economy. An aluminum truck needed to be safer, lighter, have increased payload, haul more, and have improved fuel efficiency. After driving the prototypes, Ford knew it was ready to move forward. Once the aluminum truck was ready to build, the next challenge was quickly transforming the plant.

Performance CNG wants to crowdfund natural gas-powered Ford Mustang

Soliciting investments to develop a street-legal compressed natural gas (CNG) powered Ford Mustang that can deliver 470 horsepower certainly wouldn't make sense on a site called Indiestopstop. Nope, Indiegogo is the more-appropriately-named site that one Michigan entrepreneur is using to try and crowdfund his CNG 'Stang. He's looking to raise $55,000. Michigan's Daryl Patrishkoff and his company Performance CNG LLC showed off their converted 2003 Mustang last year at the Woodward Dream Cruise in Royal Oak, MI in an effort to get some exposure for the car, which can run on both gas and CNG. The company and its three-man team is looking to further develop the project in the name of a fueling source that is 40 percent cheaper than gasoline, throws off as much as 30 percent fewer tailpipe greenhouse gas emissions and makes the country less dependent on foreign oil. Performance CNG estimates that just 120,000 of the world's 15 million CNG-powered vehicles are in the US and is calling for more. As for the $55 grand, Patrishkoff estimates that more than half of that amount would be committed to the Environmental Protection Agency (EPA) testing of emissions, fuel economy and horsepower. The problem? As of right now, only $150 has been raised. Check out Performance CNG's press release below and see the fundraising effort on Indiegogo here. Eco-Friendly Muscle Car? CNG vehicles save money, emit less pollution and creates jobs from American-mined fuel SHELBY TOWNSHIP, Mich., May 5, 2014 /PRNewswire/ -- Daryl Patrishkoff of Shelby Township, MI, has a vision for the American automotive industry. He firmly believes that our fuel of choice should be Compressed Natural Gas (CNG), not gasoline. Until the full CNG infrastructure is in place a Bi-Fuel vehicle, fueled by either CNG or gasoline upon the drivers command, is the bridge vehicle that can lead this transition. Patrishkoff heads up a (3) man technical team developing this technology. The advantages are: 40 percent savings in fuel costs at the pump 25-30 percent reduction in harmful emissions 100 percent US provided natural gas Meaningful employment for the US economy The most important benefit, however, is that a CNG-powered vehicle runs on fuel that can be mined in America, eliminating the need for foreign oil. "After decades of political rhetoric, these types of vehicles can truly lead the US to energy independence," he said.