on 2040-cars

Auto blog

Here's what the UAW will be angling for in next year's contract negotiations

The United Auto Workers union is about to enter a new round of negotiations with the Detroit Three automakers, and this time, the focus is on the end of the two-tier wage system. Introduced in 2007, the two-tier wage system was enacted to allow General Motors, Ford and Chrysler to categorize its hourly employees under two categories: Tier 1 for veteran employees with full rights and benefits, and Tier 2 for short-term or entry-level employees compensated under a different schedule. The idea was that the system would permit the automakers to invest more in their plants and hire new employees as part of their respective recovery plans without being saddled with all the costs associated with hiring full-time employees. Now that the automakers are (more or less) back on their proverbial feet, however, the UAW wants to see an end to the two-tier system, and will likely make that a center-point of its negotiations next year to replace the current arrangement that is scheduled to end in September 2015. Not all members of the UAW will necessarily be interested in ending the two-tier system, however. According to The Detroit News, some Tier 1 workers may be more interested in negotiating a raise in their hourly rate – something which they haven't received in almost a decade. Tier 2 workers, meanwhile, may be more motivated to keep the tiered system in place, as their arrangement includes provisions for profit-sharing payments that have seen the automakers pay out billions to so-called short-term employees in lump-sum payments. Reconciling the two competing demands from two categories of union members and presenting a united front in negotiations may prove the biggest challenge for the UAW's new president, Dennis Williams. And with the right to strike – something which was suspended during the last round of negotiations in 2011 – the union has a bigger bargaining chip in its pocket.

Ford recalls 90,736 vehicles due to engine valve issue

Ford will recall 90,736 vehicles as engine intake valves in the vehicles may break while driving, the National Highway Traffic Safety Administration (NHTSA) said on Saturday. The recall impacts certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine, the NHTSA said. According to documents posted by NHTSA and sourced from the automaker, "The engine intake valves may break while driving, which can result in engine failure and a loss of drive power." Following an investigation that started in January, 2022, Ford found 22 instances where "the engine intake valves fractured and fell into the combustion chamber of the engine causing catastrophic engine damage." The automaker's analysis continues: "Ford identified that the potential root cause of the failures was engine intake valve failure due to valves that exceeded the designed specification for hardness, were brittle, and more likely to fracture. Ford determined that this was due to the supplier’s grinding processes and the sensitivity of the intake valve material to grinding processes that were not within control specifications. The intake valve material was changed for vehicles produced after October 31, 2021." Fixing the problem will require replacement of the entire engine. "Dealers will inspect each vehicle to determine its cumulative number of engine cycles. For vehicles that do not meet the engine cycle threshold, dealers will accumulate high revolutions per minute (rpm) engine cycles per a service procedure. Engines will be replaced on vehicles that do not pass the engine cycle accumulation," Ford says.

Ford Mustang Shelby GT500 has a bit of a dyno issue

We're of the mind that each and every dyno should come with Murphy's Law painted in big, visible letters down the side. For every ten successful dyno runs out there, it seems there's one where events to horribly wrong. Take, for example, the video below. The clip shows what happens when a Ford Shelby GT500 and a mobile dyno have a bit of a disagreement at the Performance Expo 24 in Sherbrooke, Quebec. We won't spoil the results for you, but we will say there's some substantial carnage involved.
It's unclear just how much damage ensues from the dust up or whether anyone was harmed in the incident, but from the looks of things, everyone made it out without serious injury. If only we could say the same for the machines involved. Check out the video below.