2014 Ford F150 on 2040-cars

Auto blog

Junkyard Gem: 1993 Mercury Topaz GS Sedan

As long as the Mercury brand existed — a period spanning the 1939 through 2011 model years — nearly every Mercury sold in the United States was more or less a redecorated Ford model. The Torino had its Montego sibling, the Crown Victoria had the Grand Marquis, the Cougar was based on everything from the Mustang to the Mondeo, and so on. Naturally, when the folks in Dearborn developed the Ford Tempo compact, a Mercury version had to be created. This was the Topaz, with the official launch of both cars taking place on the deck of the aircraft carrier often referred to as the USS Decrepit. You can't make this stuff up! The Tempo/Topaz, also known as the Tempaz, has largely faded from our collective automotive memory by now, since it broke no significant new engineering or styling ground (this story would be much different if Ford had only put the amazing straight-eight "T-Drive" Tempaz powertrain into production) and didn't have any endearing features other than being a cheap domestic competitor to the Toyota Corolla and Nissan Sentra. Still, close to 3 million Tempazes left North American Ford and Lincoln-Mercury showrooms during the 1984-1994 period. As you'd expect, most of these disposable cars disappeared from both the street and the car graveyard long ago. It takes a very special Tempaz for me to break out my camera while I'm patrolling my local wrecking yards; generally, this means an ultra-rare all-wheel-drive version or at least a very early model in super-clean condition. Today's Junkyard Gem is neither, but I took one look at this spectacular Bordello Red crypto-velour-and-slippery-plastic interior and recognized that this was no ordinary junkyard Mercury. It appears that Mercury had dropped the idea of clever names for base-grade seat fabrics by the time of the Topaz, referring to this stuff as just "cloth" in all the brochures I could find. That's too bad, because Mercurys had cool names for upholstery (e.g., Chromatex) in the old days. The interior is in very good condition but the steering wheel shows substantial wear, so I think this is a high-mile Topaz that got meticulous care from its owner or owners. Ford used five-digit odometers on these cars until the end of production, however, so we'll never know if this reading indicates 65,404 miles or 365,404 miles. The body is very straight, but there's some nasty corrosion behind the right front wheelwell.

The 11 most expensive American cars ever

Here's a Pro Tip for all you would-be classic car investors out there: buy Ferraris. With the Pebble Beach festivities kicking off this week, including any number high end car auctions, we thought it would be entertaining to compile a list of some to the most expensive cars ever sold with the bang of a gavel. Trouble is, once you get past the splendor of everyone's favorite Italian sports car maker, that list is pretty boring.
Ferrari dominates the all-time auction sales list; seven of the top ten most expensive cars sold wear the Cavallino Rampante badge, as well as more than half of the top fifty. Sure, a nearly $30-million Mercedes-Benz W196 racecar might be the new top dog as of last year, but it's even possible that Ferrari could take that title back in Monterey this weekend. Long story short: we think a list of the most expensive American cars ever sold at auction is a lot more entertaining to read. Hell, our list has a friggin' Batmobile on it, how can it go wrong?
Follow on below for the top ten cars that are red, white, blue and a whole lot of green.

Ford, Alcoa announce next generation of aluminum lightweighting for F-150

Ford likes what it has seen with the use of aluminum in its world-beating F-150 pickup trucks. Now, the Blue Oval is working with Alcoa to use that company's Micromill material to increase the amount of aluminum in Ford vehicles. In fact, Ford will start using Micromill on 2016 model-year F-150s later this year, and will double the material's use in 2017. The purpose, as you might suspect, is light weighting, which allows Ford to boost towing capacity while adding as little weight as possible. Ford will be the first automaker to use Micromill, and will use it in both structural components and exterior panels. Micromill's rolling-mill system cuts the time it takes to turn molten metal into coil to 20 minutes from about 20 days. Already, Ford has had positive results by using aluminum on its leading pickup truck model. In April, it was announced that the 2015 Ford F-150 achieved a five-star Overall Vehicle Score in the National Highway Traffic Safety Administration's testing. Safety features like inflatable seat belts, adaptive steering columns and a forward collision warning system helped matters. General Motors may have taken note of those results, even after running an ad campaign touting its continued use of steel over aluminum. Last month, GM said it would sink $877 million into its Flint, MI, truck factory. Reuters said much of the expense was to convert many of the bodies for models like the Chevrolet Silverado and GMC Sierra pickups into aluminum. You can take a look at Ford's press release below. Ford Motor Company and Alcoa Inc. are collaborating to produce next-generation automotive aluminum alloys that are more formable and design-friendly. Ford will use Alcoa's Micromill® material in multiple components on the 2016 F-150 – becoming the first automaker to use the advanced automotive aluminum commercially. The companies entered into a joint development agreement to collaborate on next-generation aluminum alloys for automotive parts using Micromill™ technology. ''Light-weighting enables us to design vehicles with great customer attributes – like the F-150, which can tow more, haul more, accelerate quicker and stop faster than the previous F-150, and is more fuel-efficient than ever," said Raj Nair, Ford group vice president and chief technical officer, Global Product Development.