2007 Ford F-150 Fx4 Crew Cab Pickup 4-door 5.4l on 2040-cars

Auto blog

Kawei K1 pickup blatantly copies Ford F-150

The Chinese auto industry used to be looked at as a joke full of products blatantly copied from foreign vehicles. However, companies like Qoros and others show that the country's automakers have taken big steps in terms of original design. It doesn't look like every automaker there is ready to put down the tracing paper yet, though. Case in point: The Kawei K1 pickup pictured above, which is an obvious rip-off of the Ford F-150. In fact, the company isn't even hiding it. Kawei deserves a little credit for its openness. In describing the new model, it says: "No matter the black net grille and the outline of the headlamp, even if the styles of fog lamp and engine cover, it looks the same as Ford Raptor." It also admits that spelling out the model name on the hood is inspired by Land Rover. It's available with either a 2.4-liter, gasoline-fueled four-cylinder producing 141 horsepower and 148 pound-feet of torque (elsewhere it also lists it as having 162 lb-ft) or a 3.2-liter six-cylinder diesel with 106 hp and 181 lb-ft. Regardless of engine, power is sent to the rear wheels through a five-speed manual gearbox. The trucks cost around 100,000 Yuan ($16,033). So at least the K1 is a reasonably priced knockoff. According to Car News China, the K1 is actually selling in small numbers. The company made 10,000 of them last year and even exported some to Africa and the Middle East. Kawei's factory is doubling in capacity this year to build even more. You can read more about the truck on the company's website in some very mangled English. Featured Gallery Kawei K1 Pickup View 11 Photos News Source: Kawei via Car News ChinaImage Credit: Kawei Beijing Motor Show Ford Truck Diesel Vehicles Beijing 2014

Ford recalls 9,900 vehicles across two campaigns

Ford is recalling a total of 9,885 vehicles in two campaigns. The Basics: In one recall, Ford will recall 9,017 examples of the 2013 Escape with build dates from January 11, 2012, to April 1, 2013, and the 2013-2014 Focus ST produced between May 3, 2012, and October 14, 2013. The Problem: Splices in the engine wiring harness might not have enough compression, and this can cause the manifold absolute pressure sensor to send incorrect signals to the powertrain control module. This issue could cause the engine to stall. Injuries/Deaths: None reported. The Fix: Dealers will replace the current crimped splices with new splices, according to the National Highway Traffic Safety Administration. If You Own One: The repair campaign will begin on January 4, 2016. More Information: Ford recalled the 2013 Escape and Focus ST in August 2014 for the same problem, and this is an expansion of that campaign, according to company spokesperson John Cangany to Autoblog. The Basics: In the smaller of the two campaigns, Ford will recall 868 examples of the 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and MKT. The Problem: The fuel delivery module can crack, which would cause a fuel leak. Injuries/Deaths: None reported. The Fix: Dealers will replace the fuel delivery module. If You Own One: Owners should receive notice soon because NHTSA's report says the recall begins in December. More Information: According to Cangany, this recall is an expansion of a campaign from 2013 for these vehicles. RECALL Subject : Engine Wiring Splices may cause Stall Report Receipt Date: DEC 02, 2015 NHTSA Campaign Number: 15V813000 Component(s): ELECTRICAL SYSTEM Potential Number of Units Affected: 9,017 All Products Associated with this Recall Vehicle Make Model Model Year(s) FORD ESCAPE 2013 FORD FOCUS 2013-2014 Details Manufacturer: Ford Motor Company SUMMARY: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM). CONSEQUENCE: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.

3dCarbon now offering body kit for Ford Fusion

A factory-backed body kit by 3dCarbon is now available to Ford Fusion owners who want their car to stand out from the crowd while not being too flashy. The body kit adds a more aggressive front spoiler, side skirts, rear body trim and spoiler that are, in fact, integrated quite nicely into the Fusion's already-comely styling, just as 3dCarbon claims. All Fusions with the kit also receive dual exhaust ports with the stainless-steel exhaust surrounds usually reserved for the Titanium package Fusion EcoBoost models.
A nice detail of 3dCarbon's injection-molded urethane body kit is that it has undergone crash testing to certify that it can withstand crashes up to five miles per hour. Because of this, the kit is warrantied by 3dCarbon for five years or 50,000 miles, much like Ford's warranty on its own parts. In fact, the kit is available through participating Ford dealers and can be financed through Ford Motor Credit. Buyers can purchase the kit - pre-painted or unpainted - and install it themselves, or it can be purchased with a new Ford Fusion and installed at the dealer, pre-painted to factory specifications. Of course, it can also be ordered directly from the source. Take a look at the press release below for more detailed information on the body kit, and let us know what you think of it in Comments.