65 Ford F100 Pick Up on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

3dCarbon now offering body kit for Ford Fusion

A factory-backed body kit by 3dCarbon is now available to Ford Fusion owners who want their car to stand out from the crowd while not being too flashy. The body kit adds a more aggressive front spoiler, side skirts, rear body trim and spoiler that are, in fact, integrated quite nicely into the Fusion's already-comely styling, just as 3dCarbon claims. All Fusions with the kit also receive dual exhaust ports with the stainless-steel exhaust surrounds usually reserved for the Titanium package Fusion EcoBoost models.
A nice detail of 3dCarbon's injection-molded urethane body kit is that it has undergone crash testing to certify that it can withstand crashes up to five miles per hour. Because of this, the kit is warrantied by 3dCarbon for five years or 50,000 miles, much like Ford's warranty on its own parts. In fact, the kit is available through participating Ford dealers and can be financed through Ford Motor Credit. Buyers can purchase the kit - pre-painted or unpainted - and install it themselves, or it can be purchased with a new Ford Fusion and installed at the dealer, pre-painted to factory specifications. Of course, it can also be ordered directly from the source. Take a look at the press release below for more detailed information on the body kit, and let us know what you think of it in Comments.

Ford recalls over 953,000 vehicles to replace Takata airbag inflators

DETROIT — Ford is recalling more than 953,000 vehicles worldwide to replace Takata passenger airbag inflators that can explode and hurl shrapnel. The move includes over 782,000 vehicles in the U.S. and is part of the largest series of recalls in U.S. history. Included are the 2010 Ford Edge and Lincoln MKX, the 2010 and 2011 Ford Ranger, the 2010 to 2012 Ford Fusion and Lincoln MKZ, the 2010 and 2011 Mercury Milan, and the 2010 to 2014 Ford Mustang. Some of the recalls may be limited to specific geographic areas of the U.S. Takata used the chemical ammonium nitrate to create an explosion to inflate airbags. But it can deteriorate over time due to heat and humidity and explode with too much force, blowing apart a metal canister designed to contain the explosion. At least 23 people have been killed worldwide and hundreds injured by the inflators. Ford says it doesn't know of any injuries in vehicles included in this recall. Dealers will replace the inflators. Ford will notify owners about the recall starting on Feb. 18, and the company has replacement parts available for dealers to order, said spokeswoman Monique Brentley. In previous Takata recalls, parts availability had been an issue. Owners can go to this Ford website and key in their vehicle identification number to see if their cars and SUVs are being recalled. The same information will be available soon at the NHTSA recall website. More than three years after the U.S. National Highway Traffic Safety Administration took over management of recalls involving Takata inflators, one third of the recalled inflators still have not been replaced, according to an annual report from the government and a court-appointed monitor. The report says 16.7 million faulty inflators out of 50 million under recall have yet to be replaced. And 10 million more inflators are scheduled to be recalled this month, including the Ford vehicles. Safety advocates said the completion rate should be far higher given the danger associated with the inflators. The recalls forced Takata of Japan to seek bankruptcy protection and sell most of its assets to pay for the fixes. The inflators grow more dangerous as they get older because ammonium nitrate deteriorates due to high humidity and cycles from hot temperatures to cold. The most dangerous inflators are in areas of the South along the Gulf of Mexico that have high humidity. Related Video: