2007 Eddie Bauer Used 4l V6 12v Automatic Rwd Suv on 2040-cars

Auto blog

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

Ford builds Lightweight Concept with Fusion shell [w/video]

It's a fairly well known fact that removing weight from a car is essentially a panacea for many of the modern automobiles problems. Does it handle like crap? Remove weight. Underpowered? Don't add power; trim the fat. Need to improve fuel economy? It's diet time.
Actually executing a major weight reduction program, though, much like with human beings, is no easy task. Unlike you or I, where motivation is the issue, the prohibitive measure in trimming a car's waistline is money. Lightweight materials are expensive, with carbon fiber and carbon-fiber reinforced plastic still primarily in the domain of higher end vehicles. Even aluminum construction, pioneered on a mass-produced level by Audi and Jaguar, is only now starting to make its way into the mainstream, thanks to the upcoming Ford F-150.
With this concept, though, Ford is attempting to show that a mass-produced, lightweight vehicle isn't too far off. This is the Lightweight Concept, and while it may look like a Fusion, it weighs as much as a Fiesta. For reference, the lightest Fusion available to the public is the 3,323-pound, 2.5-liter model with a manual transmission. A manually equipped, 1.6-liter Fiesta, meanwhile, is just 2,537 pounds.

Recharge Wrap-up: Atieva making EV with former Tesla talent, Holland lowers PHEV incentives

A reduction of tax incentives on company cars in Holland is expected to put the brakes on plug-in hybrid sales. Cars are taxed at an average of 25 percent, with plug-in hybrids taxed at just seven or 14 percent, depending on emissions. Taxes on PHEV company cars will increase to 14 and 21 percent. With company car leases making up a third of vehicle sales in 2014, the uptake on PHEVs "will likely go back to regular volumes," according to Volvo's Christiaan Krouwel. It could be a boon for battery electric cars, as their tax rate will remain at four percent for company cars. Read more at Automotive News Europe. Ford is testing cylinder deactivation in its 1.0-liter EcoBoost engine. On-road prototype testing has shown improvements in fuel economy of as much as six percent. Ford engineers developed a system using a new dual mass flywheel, pendulum absorber, and tuned clutch disc to allow cylinder deactivation under a wider range of speed and engine loads with less NVH. "The highest priority in the development of new combustion engines for automotive applications is the ongoing reduction of fuel consumption," says Ford's Andreas Schamel, presenting Ford's findings to the Vienna Motor Symposium. Read more at Green Car Congress or in the press release from Ford. Atieva is building an EV with the help of numerous former Tesla employees. The Silicon Valley-based startup was founded in 2007 by a former Tesla vice president, and its roster includes 12 other former Tesla employees. Already well funded, Atieva is now looking to fill its ranks with more talent, with 32 engineering positions, two recruiter positions and other job openings posted at its website. As for the EV it is working on, Atieva says it is "redefining what a car can be, by building an iconic new vehicle from the ground up." Read more at Charged EVs. Testing shows that Joule ethanol, made from recycled CO2, meets standards for use in the US and Europe. In partnership with Audi, Joule has been working toward making its recycled CO2 fuels ready for commercialization. "We are pleased to achieve another critical step towards our planned near-term delivery of fuel-grade ethanol from recycled CO2," says Joule President and CEO Serge Tchuruk. "Using waste CO2 as a feedstock, our technology has the two-fold advantage of reducing greenhouse gas emissions and producing cost-competitive, drop-in fuels." Joule will use these test results to get government approval for the use of its ethanol in highway fuel.