2000 Ford Explorer Sport Sport Utility 2-door 4.0l on 2040-cars

Auto blog

Did a US automaker blow the whistle on Hyundai, Kia fuel economy issue?

In all of the most hotly contested mainstream segments of the motoring universe, the difference of one mile per gallon averaged on a widow sticker can mean the difference between a sale and a walk-off - to say nothing of two or three mpg. So, when Hyundai and Kia were forced to reveal that many of their 40-mpg ratings were actually 38s and 37s, well, it made for big news.
It also, conceivably, made for a competitive disadvantage immediately, when the Korean automakers' products were being shopped versus the guys down the block. And it's that disadvantage that makes a recent story from Automotive News so juicy.
AN is reporting that Margo Oge, former head of the Environmental Protection Agency's Office of Transportation and Air Quality, got a tip in 2010 that Hyundai/Kia were "cheating" to get its impressive fuel economy numbers. The tip, said Oge (who retired from the EPA this past September), came from a senior vice president from a domestic automaker. The source was credible enough for Oge to launch an audit of the Hyundai figures, which ultimately lead to the debacle that we reported on a few months ago, and that the Korean company has been trying to bounce back from ever since.

Mustang parts under the new Lincoln Aviator mean good things for Ford

NEW YORK — As we mentioned last night, underneath the new Lincoln Aviator "concept" there appears to be an independent rear suspension lifted right from the Ford Mustang parts bin. And while it's pretty cool on its face that Mustang rear-drive platform bits are being reused in the broader Ford universe, what this means for the next Explorer could be really cool. A quick caveat: The Aviator here in New York is very close to the production version, but it's not technically a production car. It looks hand-built, with temporary exhaust and some show-car touches. The suspension underneath looks exactly like a Mustang's, but the actual production Aviator will almost certainly use beefier components with the same basic design and geometry, since the Aviator will be much heavier than the smaller Mustang. That being said, we're fairly confident that even at this early stage, the Mustang-derived suspension seen in New York is a preview of what'll be under the production Aviator. Furthermore, Ford won't say it, but based on what we're seeing on Aviator, it's a safe bet that Ford will utilize the Aviator platform for the next Explorer. That would enable the economies of scale necessary to produce a brand new rear-drive-based SUV platform in the first place. It also means that the Explorer should be available without AWD — and given the stable of powerful EcoBoost engines, and the competent 10-speed automatic in the parts bin, a rear-drive Explorer has a shot at being a decent driver. Aviator wouldn't go rear-drive-based if driving dynamics weren't important; Explorer should inherit these priorities. More evidence: The Explorer spy shots we saw back in February sure share the Aviator's general proportions. Even back then, before Aviator was revealed, we were hypothesizing that an EcoBoost 3.5-liter-powered version could boast as much as 400 horsepower, if the Expedition's tune were adopted. Suddenly, the Explorer seems very interesting. So, an EcoBoost, rear-drive Explorer sure sounds like something Ford Performance would be interested in, right? We knew an Explorer ST is coming, but with 365-400 horsepower potential and a chassis designed with dynamics in mind, it doesn't seem like as much of a stretch as the Edge ST. And a performance-oriented AWD system is a possibility, too. That's an area where Ford has been gathering experience at a rapid pace. What do we not expect from a new Explorer? A V8.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.