2000 Ford E-350 12 Passenger Van Gr8 Service Records Rare Xlt 6.8 V10 Very Clean on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ford ending Focus, C-Max production in Michigan after 2018

Ford will no longer produce the Focus and C-Max at its Michigan Assembly Plant in Wayne, MI, beyond 2018. United Auto Workers vice president Jimmy Settles confirmed this in a letter Thursday, which was posted on Twitter. According to the UAW Ford Department's tweet, production of the Focus and C-Max will shift to Mexico. Ford isn't confirming this, though – a spokesperson tells Autoblog, "We didn't say that." Instead, Ford issued the following statement about the matter: We will move production of the next-generation Ford Focus and C-Max, which currently are built at Michigan Assembly Plant, beginning in 2018. We actively are pursuing future vehicle alternatives to produce at Michigan Assembly and will discuss this issue with UAW leadership as part of the upcoming negotiations. Earlier this year, Ford announced layoffs of 700 employees at the Michigan Assembly Plant, citing slow sales of both the Focus and C-Max. The MAP was once heralded as a flexible, futuristic facility when it was retooled for C-segment car production in 2009. Prior to that, the Ford Expedition and Lincoln Navigator SUVs were built at the Wayne facility. It also produced the iconic Ford Bronco. The future of the MAP is uncertain, but the UAW remains hopeful. In Settles' letter, he writes, "We are extremely confident that a new product commitment will be secured during the upcoming 2015 negotiations and that the Michigan Assembly Plant will maintain a full production schedule." Related Video:

Ford partnering with MIT, Stanford on autonomous vehicle research

Ask any car engineer what's the biggest variable in achieving fuel economy targets, and he'll tell you "the driver." If one human can't understand human driving behavior enough to be certain about an innocuous number like miles per gallon, how is an autonomous car supposed to figure out what hundreds of other drivers are going to do in the course of a day? Ford has enlisted the help of Stanford and the Massachusetts Institute of Technology to find out.
Starting with the automated Fusion Hybrid introduced in December, MIT will be developing algorithms that driverless cars can use to "predict actions of other vehicles and pedestrians" and objects within the three-dimensional map provided by its four LIDAR sensors.
The Stanford team will research how to extend the 'vision' of that LIDAR array beyond obstructions while driving, analogous to the way a driver uses the entire width of a lane to see what's ahead of a larger vehicle in front. Ford says it wants to "provide the vehicle with common sense" as part of its Blueprint for Mobility, preparing for an autonomous world from 2025 and beyond.