2010 Dodge Viper Srt-10 Coupe 2-door 8.4l on 2040-cars

Auto blog

Dodge could enter Peugeot's Le Mans-bound 9x8 hypercar in IMSA races

Fiat-Chrysler Automobiles (FCA) and PSA Group merged under the Stellantis umbrella in early 2021 to achieve economies of scale, and this benefit could surprisingly extend to racing. Executives are debating whether to give Dodge its own version of Peugeot's recently-unveiled 9x8 hypercar to race in America, according to a recent report. "While we only heard [the new rules] confirmed a week ago, it has certainly led to some very open discussion, not only about whether Peugeot might add races in the United States, but also about whether the spine of this car might have opportunities with other brands in the Stellantis Group. There are no conclusions yet, but there are now open discussions," affirmed Jean-Marc Finot, the Senior Vice President of Stellantis, in an interview with Racer. His comments refer to an agreement signed in July 2021 by the Automobile Club de l'Ouest (ACO), the Federation Internationale de l'Automobile (FIA), and the International Motor Sports Association (IMSA). They chose to align their technical regulations to let manufacturers compete in different events on both sides of the pond without going through the resource-consuming process of developing a specific car for each series. As of writing, the Le Mans Hypercar (LMH) and Le Mans Daytona h (LMDh) categories fall under the newly-announced common set of rules. On the surface, this means Peugeot could enter its 9X8 (pictured) in the WeatherTech SportsCar Championship as soon as the 2023 season. While this is seemingly under consideration, Peugeot has little to gain from winning a major race in the United States. It hasn't sold cars here since 1991, and its long-mooted comeback was canned after PSA merged with FCA. Giving a variant of the 9X8 to Dodge is a more credible possibility, according to Racer. If not Dodge, then who else? Chrysler hasn't been linked to racing or performance for decades. Jeep is no stranger to performance vehicles, but IMSA would be pushing it. Ram is Ram, while Fiat, Alfa Romeo, and Maserati are rooted in Europe. The rest of the Stellantis brands (like Opel, Lancia, and Citroen) are not distributed in America. Nothing is official, and the publication stressed it's unclear whether Dodge will commit part- or full-time to the series (assuming the program receives the green light). Finot underlined the parallel car would use the 9X8's "spine," so don't expect to see a Peugeot hypercar with a Dodge emblem driving flat-out on the Sebring International Raceway.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2019 Dodge Charger SRT Hellcat is getting a facelift

The Challenger Hellcat won't be the only Mopar muscle car getting an update for the new model year. One of our spy photographers caught an updated 2019 Dodge Charger SRT Hellcat testing near the SRT office. It appears that the car will continue on mostly unchanged, since everything behind the fenders is uncovered and unchanged. But the fascia must be getting some noteworthy changes considering how well it's hidden. And it's really, really well-hidden. It's extremely difficult to see through this covering. Whatever changes have been made still aren't going to be massive. It looks like the basics remain the same, including the large center grille in the bumper flanked by two outboard inlets that lack fog lights. The grille appears to still connect with the headlights, and the grille is pinched in the middle. Odds are, the front fascia is the only major difference on the 2019 Charger Hellcat, just as the twin-scoop hood on the Challenger Hellcat is the only major difference on that model. Under the hood will likely be the same 707-horsepower supercharged V8. This Charger prototype also sports the same Brembo brakes as the current model. The full reveal will probably come this summer along with the Challenger. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Featured Gallery 2019 Dodge Charger SRT Hellcat Spy Shots View 14 Photos Image Credit: SpiedBilde Spy Photos Dodge Performance Sedan dodge charger srt hellcat