1992 Dodge Stealth Twin Turbo Awd Upgraded Stereo System And Wheels Great Shape on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.

Fiat Chrysler taps Amazon, Shell execs to fill roles

MILAN — Fiat Chrysler Automobiles is tapping executives from Amazon and Shell Oil Company with previous automotive industry experience to fill its ranks. CEO Mike Manley said in a letter to employees Thursday that Mark Stewart would join FCA as chief operating officer of North America from Amazon, "a company known for its culture of innovation, and obsession with delivering incredible value to customers." At Amazon, Stewart led teams focused on advanced robotics, artificial intelligence and automation methods. He previously was COO of ZF TRW automotive components supplier. Niel Golightly was named head of global communications. He was most recently Shell's vice president for external relations in North and South America, with a focus on reputation, brand and stakeholder engagement beyond communication strategies. He previously held roles at Ford Motor Company. Related Video: Image Credit: REUTERS/Rebecca Cook Hirings/Firings/Layoffs Alfa Romeo Chrysler Dodge Fiat Jeep RAM FCA Amazon shell Mike Manley