2004 Dodge Sprinter 2500 Long & Tall Passenger Van 5-door 2.7l on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Mopar Hellephant is sold out, but here are 4 other awesome crate V8s to try

Despite a relatively enormous $30,000 price tag, Mopar's 1,000-horsepower supercharged Hellephant crate engine sold out in just 48 hours. Some enthusiasts may have missed out on the crazy engine due to lack of funds, or they just assumed there would still be some Hellephants down the line. But worry not, swap-happy gearheads. There are plenty of V8s in the world to pick from, and we highlighted four favorites. They're not as powerful, but they're all cheaper, and still have a lot to offer. Mopar 6.2L Hellcrate Odds are a lot of prospective Hellephant buyers were Mopar fans to begin with, so we'll start the list with the next-most-potent offering: the Hellcrate. This is the same supercharged 6.2-liter V8 found under the hood of the Dodge Charger and Challenger Hellcats and the Grand Cherokee Trackhawk. It makes 707 horsepower and 650 pound-feet of torque like those cars, too. It's also about $10,000 cheaper than the Hellephant engine at $20,020, and that leftover money can be used to finish the project or for aftermarket upgrades to get it closer to the Hellephant's output. GM LS9 6.2L The Hellcrate isn't the only factory supercharged crate engine on the market. From General Motors comes the supercharged 6.2-liter LS9 V8. This is the engine that was used in the C6 Corvette ZR1. At 638 horsepower and 604 pound-feet of torque, it doesn't make as much power or torque as the Hellcrate. But it does boast a dry sump oil system. So instead of pumping oil out of a pan at the bottom, the engine uses an oil tank mounted remotely that pumps oil into the engine. This means the engine is shorter overall, and can be mounted lower for a better center of gravity. It also means that there's almost no risk of running the engine dry in hard cornering, as could happen with a normal oil sump where the oil can slosh to the side without the oil pump. Basically, it offers some major benefits if you want supercharged V8 power for a road course car. It's also a tad cheaper than the Hellcrate at $18,149. But get one while you can, because GM is only selling what's left from when it was building the C6 ZR1. Ford Aluminator 5.2XS Our pick from the Blue Oval lacks a supercharger, but it's still pretty sweet.

Baby Ford Ranger and electrified Dodge Challenger? | Autoblog Podcast #569

In this week's Autoblog Podcast, Editor-in-Chief Greg Migliore is joined by Green Editor John Beltz Snyder. They address a couple interesting news topics, including an upcoming Ford pickup that's smaller than the Ranger, as well as a future electrified Dodge Challenger. They also opine about the new Honda Urban EV prototype that's scheduled to debut at the Geneva Motor Show. Then they talk about the cars they've been driving, including the new Subaru Crosstrek Hybrid, Volvo V60 and Audi A6. Finally, they take a question from Autoblog's recent Reddit AMA to help spend a Redditor's money. Autoblog Podcast #569 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Rundown Ford Focus-based pickup Electrified Dodge Challenger Honda Urban EV Cars we've been driving 2019 Subaru Crosstrek Hybrid 2019 Volvo V60 2019 Audi A6 Spend My Money Feedback Email – Podcast@Autoblog.com Review the show on iTunes Related Video: Green Podcasts Audi Dodge Ford Honda Subaru Volvo Truck Coupe Crossover Hatchback Wagon Electric Hybrid Performance