2004 Dodge Sprinter on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Rare Dodge Daytona found in barn heads for auction

An American icon is headed to Mecum's Kissimmee, Florida auction next January. Charlie Lyons, owner of a restoration shop focused on old Chrysler products, got a lead on a two-owner 1969 Dodge Charger Daytona that had been sitting in a barn in Glenwood, Alabama for decades. Dodge built 560 Charger Daytonas (Canada and US production) to homologate the model for NASCAR racing, and then that car and the successor Plymouth Superbird terrorized NASCAR tracks for 18 months. The production car, however, 18 feet long and considered ugly, wasn't popular at the time, so many were beat up or simply disappeared. Around 385 are thought to exist today. Lyons said the first owner of this car was the town judge, who bought it for his wife. In 1974 the second owner - just 18 years old at the time - bought it for $1,800 so he could drive it to Panama City, Florida, for Spring Break, and had flames painted on the front fenders and the scallops trimmed in white. Otherwise this barn find is complete and stock, with matching numbers throughout, R4 Charger Red paint and a white tail, bucket seats, center console, three-speed TorqueFlite automatic, and 20,553 miles on the 440-cubic-inch Magnum V8. Hot Rod has the long story of how Lyons found the car and convinced the owner to sell for what he jokingly called "a shoebox full of folded money." Hagerty says a concours-worthy model can command $262,000. Mecum's pre-sale estimate for this Charger Daytona is $150,000 to $180,000. That sounds steep, but Mecum did sell another perfectly restored Hemi-powered 1969 Charger Daytona for $900,000 at this year's Kissimmee auction to actor David Spade. Related Video:

Classic Design Concepts has another riff on the widebody Challenger

Dodge is secretly working on a widebody Hellcat-powered Challenger dubbed the ADR. But for those that can't wait a few years, there's this – Classic Design Concepts' Group 2 Widebody Challenger that was unveiled at SEMA. The original Group 2 Widebody Challenger from CDC made its debut at SEMA back in 2008, but was given a new look for this year's trade show. The car, which you can scrutinize in the gallery above, features a bright red paint job with a blacked-out American flag on the left rear fender and "Hemi" in yellow on the right side. The wheels are also color-coated to match the rear billboard fenders, with the right side being finished in yellow and the left side a dark gray. CDC's body kit is wide, slammed to the ground, and menacing. And if you happen to forget that this is a widebody Challenger, because the extra six inches of width are hard to miss, there's a clear reminder on the back of the car. Related Video: Featured Gallery Classic Design Concepts Group 2 Widebody Challenger: SEMA 2016 View 11 Photos Image Credit: Live photos copyright 2016 Drew Phillips / Autoblog Aftermarket Design/Style SEMA Show Dodge Coupe Special and Limited Editions Performance SEMA 2016 cdc widebody