Beautiful 97 Dodge Ram B2500 Advantage Custom Van V6 Cold Ac 56 Pics No Reserve on 2040-cars

Auto blog

Stellantis aims to eliminate separate inverter, charger to improve EV efficiency

Stellantis has announced that, in collaboration with French battery company Saft and French National Center for Scientific Research, has made significant progress in eliminating two major components of an electric vehicle powertrain: the on-board charger and the power inverter for the motor. The company claims that doing this will allow for better space use in vehicles, as well as improvements in efficiency, cost and reliability of components. As a quick primer, also explained in the below video, the on-board charger and power inverter are sort of translators to get the right current to different parts of the electric powertrain. The on-board charger takes AC power from the grid and converts it to DC to charge the batteries. Then when power goes from the batteries to the electric motor, the power inverter converts that DC power back to AC. These components aren't exactly small. Frequently you'll find them packaged somewhere under the hood. What Stellantis and its cohorts have developed, and have been using on a test vehicle since last summer, are small power inverter boards that can be mounted very closely to the battery packs. They can handle both conversion needs, for charging and discharging, instead of needing two separate devices. The most obvious perk to this is that you can do away with those traditional components and free up more space, either for making smaller vehicles without losing interior volume, or adding space to a vehicle that wouldn't have had it otherwise. There's the additional benefit of reduced weight, something that EVs struggle with. Stellantis also claims improvements in efficiency, reliability, and cost, however, it didn't go into detail as to how this setup would do that exactly. We'll try to get in touch with representatives from Stellantis in order to get more information. We're still a ways out from seeing this technology in production Stellantis vehicles. The company said it aims to apply it to vehicles by the end of the decade. Saft is also looking at using it on stationary battery systems as well. So maybe we'll see it on a 2029 Ram 1500 REV, but for now, we'll be living with traditional chargers and inverters. Related Video: Green Alfa Romeo Chrysler Dodge Fiat RAM Technology Electric

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

2015 Dodge Charger configurator opens up shop

Itching to get your hands on a new 2015 Dodge Charger? Your day is almost nigh, my friend While you're waiting, you can spec out how you'd want your muscle sedan to look as Dodge has included the revised four-door in its online configuration tool. Though it's not the most impressive or interactive of configurators we've seen, the site lets you choose any color you want (from the limited array available anyway) along with all the key options packages and such. First you'll need to choose a trim level though, but we're afraid the Hellcat version isn't part of this site, and the SRT site hasn't launched a configurator yet for the world's fastest production sedan, so you'll have to choose between SE, SXT and R/T trim levels. Related Video: