A/c Air Conditioning Plumbers Electricians Contractors Commercial Plumbing Cargo on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2019 Dodge Challenger SRT Hellcat Redeye priced $14,000 below Demon

Steve Beahm, head of Passenger Car Brands at Dodge, SRT, Chrysler, and Fiat, told Motor Trend that the 2019 Dodge Challenger SRT Hellcat Redeye is "a Hellcat that's been possessed by a Demon." Turns out the Hellcat Redeye was also possessed by The Ghost of Great Deals. Dodge just released pricing for the Challenger line, the crimson-eyed terror at the top starting at $69,650, which is $13,645 less dear than the $83,295 MSRP for the 2018 Challenger SRT Demon. The asterisk: the Redeye needs the same $1,345 destination charge and $1,700 gas guzzler tax as the 2018 Demon, so the difference still holds once you get the Redeye off the dealer lot. The final tally: $72,995. Torque News acquired a copy of the Challenger dealer order guide, and options on the Hellcat Redeye will run you a little more than the bucket of $1 options on the Demon. Among the list, the summer performance tires add $695, the optional 3.09 rear axle adds $1,095, a painted black hood costs $1,995, and the Widebody package adds $6,000 for it's extra 3.5 inches. According to TN, you can run a standard Hellcat Redeye up to almost $90,000, and push a widebody to $95,000. The standard Challenger SRT Hellcat gets touched by the bargain bogeyman, too: the price goes down by $5,645 for 2019 to $58,650, even though it's been uprated by ten horsepower to 717 hp, and by six pound-feet to 656 lb-ft. Out-the-door price after a $1,700 gas guzzler tax and $1,345 destination fee is $61,695. Before including destination, there's a long way down to the next model, the 485-horsepower Challenger R/T Scat Pack at $38,995. Buyers who choose the six-speed manual for this trim will pay a $1,000 gas guzzler tax. The V6-powered, 305-hp Challenger GT in two-wheel drive starts at $29,995. Sending power to all four of the GT's wheels needs $32,995 before destination. The base model, two-wheel drive SXT gets the Challenger doors open at $27,295, the all-wheel drive model costing $30,295. Related Video:

MotorWeek remembers a better time for Mitsubishi performance

Dodge still knows how to create an capable performance car – look at the Hellcats, for example – but the same isn't true for Mitsubishi. With the Lancer Evo's demise, we don't expect driving enthusiasts to clamor for any of the Japanese automaker's other products. Things used to be different, though. As MotorWeek found in its new Retro Review, the 1991 Mitsubishi 3000GT VR4 and its sibling, the Dodge Stealth R/T Turbo, were impressive sports coupes in their day. Dodge and Mitsubishi packed a bevy of cutting-edge tech into the coupes. In these trims, both sported all-wheel drive, four-wheel steering, an adjustable suspension, active exhaust, and automatic climate control. The 3000GT VR4 upped the ante even more with active aero parts at the front and rear. Their 3.0-liter twin-turbo V6 was good for 300 horsepower and 307 pound-feet, which were good numbers at the time. This pair put all their gizmos to good use, too. MotorWeek compares the all-wheel-drive system's grip levels to a Porsche 911 Carrera 4. When was the last time you heard any favorable similarity between a Mitsubishi and a Porsche? The Stealth R/T Turbo and 3000GT VR4 came from a special time for Japanese sports coupes, when every brand had a halo model. Whether you were looking at Nissan 300ZX, Mazda RX-7, Toyota Supra, or even the Acura NSX, there was a lot to like on the market. MotorWeek's latest Retro Review offers a great reminder of that period.