2001 Dodge 3500 Ram 15 Passenger Van on 2040-cars

Auto blog

Certain Chrysler owners eligible for buyback program

Certain car owners whose Chrysler vehicles contain dangerous defects will soon have a way to get rid of their lemons without losing money. As part of an agreement with federal regulators, Fiat Chrysler Automobiles has agreed to buy back more than 500,000 vehicles susceptible to veering out of control without warning at above market-value prices. The deal mainly covers certain models of RAM trucks, the Dodge Dakota pickup and Dodge Durango SUV. Further, owners of more than 1.5 million Jeep Liberty and Grand Cherokees at heightened risk for lethal fires are eligible to trade in their vehicles at above market value or, alternately, get a gift certificate if they prefer to have repairs made. Chrysler has "a heavy responsibility to make sure the products they make are safe for the traveling public," said Mark Rosekind, administrator of the National Highway Traffic Safety Administration. "... Here, we are sending an unambiguous signal to industry that if you skirt the laws or violate the law, or don't live up to the responsibility that consumers expect, we are going to penalize you." The buy-back and trade-in options for motorists come as part of an unprecedented penalty NHTSA slapped against Chrysler for violating federal motor-vehicle safety laws. Chrysler will pay a $105 million fine, the highest ever levied by the regulatory agency. In addition to the buy-backs, Chrysler also agreed to an independent monitor for three years. Investigators had outlined problems in the company's conduct in 23 recalls that affected more than 11 million defect vehicles. As part of a consent-order agreement, Chrysler acknowledged it did not notify vehicle owners of recalls in an effective manner and did not notify NHTSA of safety problems. Though those recalls affected millions of drivers, the buy-back and trade-in options are only for a small portion of the vehicles involved. Because Chrysler struggled to fix the problem and no repair was apparent, Rosekind said the buy-backs are reserved "for customers who didn't have a remedy." Buy-backs are for trucks and SUVs affected by three recalls that occurred in 2013 (recalls 13V-038, 13V-527 and 13V-529), that addressed a rear-axle pinion nut that could come loose and cause a loss of vehicle control. Those recalls covered 579,228 vehicles, including 2009-2012 Ram 1500, 2500, 3500, 4500 and 5500 trucks, 2009-2012 Dodge Dakotas, 2009 Chrysler Aspen and the 2009 Dodge Durango.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Mopar teases four of 'nearly 20' SEMA Show concepts

Yesterday it was Chevrolet. Today, Mopar has dropped some SEMA knowledge, releasing a quartet of teaser images that give us some indication of what kind of cars, trucks, and crossovers Fiat, Chrysler, Dodge, Jeep, and Ram will be showing in Las Vegas. Like Chevy, Mopar's concepts utilize both production and concept accessories, although Fiat Chrysler has gone a bit more indepth on at least one of its concepts. Immediately, the most tantalizing teaser is the one shown above. Yes, that's the back of a Challenger, and aside from the bright orange accents on the gray body, you should take notice of the badge mounted on the spoiler – yes, that says "GT AWD." To be honest, such a vehicle wouldn't be a huge shock, as both the Challenger's LX platform-mates, the Dodge Charger and Chrysler 300, are offered with all-wheel-drive options. Still, adding such a vehicle to the production cycle would give Dodge a leg up on the rear-drive only Ford Mustang and Chevrolet Camaro. Aside from that concept, FCA has also released teasers of a Ram-based concept, a 300-based concept, and what we're guessing is a Fiat 500X. We can't wait to see what the actual Fiat concept has to do with kiteboarding. As for the 300 and Ram, there's not a lot of hints on what sort of styling details they'll contain. The Chrysler has additional LED accents and what we're guessing is matte blue paint, while the Ram is based on a Hemi-powered 1500 with Rebel styling cues. This is just a very tiny sample of Mopar's final SEMA roster, which include "hundreds" of parts. There should also be a total of 20 vehicles covering all four former Chrysler Group brands, as well as Fiat. Naturally, we'll have plenty to report on each vehicle once the SEMA show kicks off in the next couple weeks.