2007 Dodge Ram 3500 Diesel 4x4 Laramie Nav Leather Bluetooth Fully Loaded Truck! on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

The Dodge Demon gets a Drag Mode and a lesson in Newtonian physics

It's Thursday morning, which means we have more news on the upcoming Dodge Demon, the pumped-up Challenger Hellcat variant that's looking to cause mayhem at a drag strip near you. This week's video, "Third Law," shows the Demon's revised suspension in action and displays another one of SRT's cryptic messages. Dodge claims that the 6.2-liter supercharged Hemi V8 in the Hellcat twins is compromised because it's fitted to a car that needs to be comfortable on the street in addition to a performer on the drag strip. Not so with the Demon, as Dodge says the car is "designed to be highly competent in all drive modes and configurations," including the all-new Drag Mode. Dodge says details about the new mode will trickle out over the next few weeks, but all the info this week focused on suspension. The "Third Law" in this week's title refers to Isaac Newton and motion: "When one body exerts a force on a second body, the second body simultaneously exerts a force equal in magnitude and opposite in direction on the first body." We're not sure what Newton would have thought seeing the sidewall wrinkling Nitto NT05R drag radials in action, but he'd probably have a reaction of some sort himself. An ideal suspension setup for the drag strip makes for a poor setup on the road. As Dodge puts it, the "old school" way to set up a drag car was to "get the quickest reacting springs upfront, the softest rebound front shocks that wouldn't restrict the springs' reaction, remove any restrictions (sway bar) and increase the compression of the rear shocks." This would give a car great front to rear weight transfer but made for very poor lateral direction control, meaning minor corrections were difficult. The Demon's Drag Mode will use electronics to give the car the best combination of launch and lateral stability. Dodge listed some of the parts to help aid in this goal. They also gave us a few equations that we can't make sense of. Let us know if you have any clues. Hardware: 35 percent lower rate front springs/28 percent lower rate rear springs 75 percent lower rate hollow front sway bar/44 percent lower rate rear sway bar Drag-tuned Bilstein Adaptive Damping Shocks Software: Rear = F/F and Front = F/S F/F – F/S maintained @ wide open throttle (WOT) F/F – F/F < WOT Traction control disabled/ESC maintained Result: 13.5=575@500 Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Thieves relieve Detroit-area Dodge dealer of $70,000 in SRT wheels

Okay Mopar fans, this won't be easy to read. A video, which has since been made private, popped up over on Reddit's Cars subreddit over the weekend and detailed the aftermath of a massive wheel heist at a metro Detroit dealership. Thieves broke into Sterling Heights Dodge and made off with at least $70,000 worth of wheels and tires. The thieves ignored the V6 models and instead targeted Hellcat, SRT392, Scat Pack, and R/T versions of the Charger and Challenger. The poor muscle cars were left sitting on blocks, with the voice behind the video saying the treatment led to underbody damage. We only counted 12 cars, but the person shooting the video said thieves targeted 14 vehicles. That works out to about $5,000 in wheels per vehicle. We've reached out to Sterling Heights Dodge general manager and the Sterling Heights Police Department for comments. We haven't heard back yet, but we'll be sure to update this post with any additional information. Oh, and if you're in metro Detroit and perusing Craigslist for a new set of alloys, we'd advise against buying Dodge wheels for the next few weeks. They might be hot. Related Video: