2005 Dodge Ram 3500 Diesel 4x4 Srw Long Bed Quad Cab 1 Owner on 2040-cars

Auto blog

2020 Dodge Challenger Drag Pak will debut at SEMA

Mopar fans have countless reasons to get hyped about the 2019 SEMA show. Speedkore is bringing a twin-turbocharged, all-wheel-drive Dodge Charger Hellcat Widebody, Mopar is bringing a done-up 1968 Dodge D200 "Lowliner," Ram is bringing a diesel 1500 overlander, and Jeep is bringing a custom off-road Wrangler. But the launch of the new 2020 Dodge Challenger Drag Pak might garner the most attention from the brand's most serious customers. Prior to the show, Mopar teased a photo and a short video clip, both showing a new Dodge Challenger from the overhead view. The white Challenger showed a wide blue stripe down the center of the car with two pinstripes along each side. "Powered by SRT" runs across the top of the windshield, and Mopar logos grace both sides of the car just beneath the side windows. Red decals run back from the rear quarter panels and connect across the rear of the car. It also has hood pins on the SRT Hellcat hood and a parachute attached the rear. There's a parachute because this is the factory turnkey drag-race-focused Dodge Challenger racecar. Mopar released no other information on what type of hardware the Drag Pak will be using, or what's under the hood, but the video gives a great preview of the exhaust note in full tire-smoke mode. As some Drag Paks in the past have dropped roughly 1,000 pounds from their production starter vehicles, the 2020 model will surely utilize plenty of weight-savings methods such as the removal of all interior comfort features that don't apply on the racetrack. Mopar has also previously altered the position of the engine and changed the wheelbase to the benefit of better weight distribution. Mopar is set to livestream the unveiling starting at 7:26 p.m. ET (that's 4:26 on the West Coast, which not coincidentally coincides the the displacement of the vintage 426 Hemi engine) on Nov. 5, 2019. Until then, check out the 2009, 2010, 2011, or 2016 Drag Paks.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

2013 Dodge Challenger V6 recalled for fire risk, owners asked not to drive

Chrysler has issued a recall for the V6 version of the 2013 Dodge Challenger (as pictured above in 2012MY) over the possibility of a wiring harness that could short circuit and lead to a fire. Owners of these V6 Challengers built from November 2012 through January 2013 are being urged to contact dealers immediately and, in the meantime, not to drive their cars or park in or near any buildings.
Chrysler estimates around 2,500 potentially affected Challengers are in owners' hands, while another 1,900 are still sitting on dealer lots. The total number of recalled vehicles is 4,459.
So far, Chrysler says that seven fires have been reported - none resulting in injuries. The company is instructing vehicle owners to contact their dealer to find out if their vehicle is included in the recall, but owners can also find the build date information of their vehicle by checking the label in the driver's door jamb.