2003 04 05 06 Dodge Ram 3500 2500 F-250 F250 F-350 F350 Cummins Powestoke 7.3 on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

FCA to recall 318,000 vehicles for faulty backup camera software

An array of 2019 and 2020 FCA vehicles are being recalled over faulty backup camera software that doesn’t meet federal regulations. According to recall documents, the backup camera may not turn off “until a drive cycle ends.” ThatÂ’s far longer than the 10-second linger time allowed by the rules, so FCA has to recall all of the vehicles to implement a fix. WeÂ’ve listed all of the vehicles involved below. 2020 Jeep Gladiator 2020 Jeep Cherokee 2019-2020 Ram 1500 2019-2020 Ram 2500  2019-2020 Ram 3500 2019-2020 Chrysler Pacifica 2019-2020 Dodge Durango 2019-2020 Jeep Grand Cherokee 2019-2020 Jeep Wrangler 2019-2020 Jeep Renegade 2019 Dodge Challenger ItÂ’s an extensive list encompassing a huge chunk of FCAÂ’s lineup in the United States. In total, FCA is recalling 318,537 vehicles. They must be equipped with the 8.4-inch or 12-inch infotainment system for the problem to present itself. FCA expects the recall to start on May 22 this year and will begin to notify owners soon. To fix the vehicles that may be affected, FCA plans to update the infotainment system at the dealer or over-the-air. If youÂ’ve noticed a screen thatÂ’s sluggish to relinquish its hold on the backup camera feed (or maybe never does), then you have this recall to look forward to. Update: FCA has provided additional information about the repair methodology. Customers will be able to receive an update over the air or have their cars updated at the dealership. Customers will begin receiving notifications this month. Related video: Recalls Chrysler Dodge Jeep Crossover Minivan/Van SUV

The Dodge Demon was developed under a cloud of smoke

The Dodge Demon needs no introduction. The car is so full of superlatives that most of it sounds unbelievable until you see and hear it in action. The car was revealed after months of teasers and cryptic messages, but the public weren't the only ones in the dark. From the start, the Demon's development was a closely guarded secret. There were even some within SRT that didn't know about the project. The people behind the car went through a lot of effort to keep it that way. At an event covering the finer details of the Demon's supercharged 6.2-liter V8, Dodge CEO Tim Kuniskis and SRT Powertrain Director Chris Cowland spoke about the smoke and mirrors used to hide the Demon's development. Work on the car progressed for nearly two years before it was made public, with just a small team having full access to the project. Numbers were altered. Secret meetings were held. SRT engineers worked nights and weekends while parts suppliers were given as little information as possible to move progress forward. Preliminary work on the Demon began in April of 2015, not long after the standard Hellcat hit the streets. The goal wasn't to create a faster Hellcat. Kuniskis said that would have been easy. They wanted a single-minded vehicle that could also be driven on the road. It's the same mindset that brought about the Dodge Viper ACR. Dodge wanted a car that could sell the brand to both enthusiasts and non-enthusiasts alike. 840 horsepower is going to raise anyone's eyebrows, including the Camry owner parked down the street. While preliminary work started in April, the final greenlight wasn't given until September. The project was originally going to revive the American Drag Racer, or ADR, name. When we saw the first hints of the Demon last fall, we labeled the spy photo above the Dodge Challenger ADR. It was set to have 10-percent more power and 20-percent more launch force than the already gut-punching Hellcat. It was also only going to have a quarter-mile time in the 10s, just slightly quicker than the Hellcat. Somewhere along the line, the team realized that the ADR wasn't enough. It was just going to be a Hellcat plus, and that wasn't exciting. The main goal was changed: 9s with light. Translated, that means a 9-second quarter mile with light under the tires (read: a wheelie). From that point forward, everything about the Demon's development, from power to suspension to weight, would be done in pursuit of that goal.