1998 Dodge Ram 3500 4x4 12 Valve Cummins Nv4500 5 Speed The Holy Grail Of Dodges on 2040-cars

Auto blog

2013 Dodge Challenger V6 recalled for fire risk, owners asked not to drive

Chrysler has issued a recall for the V6 version of the 2013 Dodge Challenger (as pictured above in 2012MY) over the possibility of a wiring harness that could short circuit and lead to a fire. Owners of these V6 Challengers built from November 2012 through January 2013 are being urged to contact dealers immediately and, in the meantime, not to drive their cars or park in or near any buildings.
Chrysler estimates around 2,500 potentially affected Challengers are in owners' hands, while another 1,900 are still sitting on dealer lots. The total number of recalled vehicles is 4,459.
So far, Chrysler says that seven fires have been reported - none resulting in injuries. The company is instructing vehicle owners to contact their dealer to find out if their vehicle is included in the recall, but owners can also find the build date information of their vehicle by checking the label in the driver's door jamb.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Highway To Hellcat: Dallas to Vegas with 2,000 HP

Fort Davis, TX. Early November. Late Sunday afternoon. The 1,200 residents of this small town are using their day of rest to quietly enjoy the breeze rolling off the hills. There's an older couple walking down the street, holding hands. A young lady working at a general store, where milkshakes and antacids are purchased at the same counter. It's a peaceful, quaint scene, right down to the tumbleweed rolling across the street and the rickety wooden porches outside the old storefronts. I hit the throttle of the 2015 Dodge Charger SRT Hellcat while turning left onto the road leading toward the town square, sending the sedan's rear end swinging to the right with a few puffs of rubbery smoke. I coast down to the 25-mile-per-hour speed limit and spot the line of Challengers, Chargers, and Vipers in my rear-view mirror, the drivers all mimicking my quick jolt of enthusiasm before pulling up the reigns on their V8s and V10s and idling into Fort Davis. Our posse would roll some 5,000 horsepower of pure American muscle into that small Texas town that day. It was only the first stop on an epic journey that would take us from Dallas to Las Vegas, on a winding route down toward El Paso, up through New Mexico, Arizona, and finally north into Nevada, ending at the ritzy Palazzo casino and hotel on the Vegas strip. It was an opportunity to see parts of America I never knew existed, and a chance to bond with some American cars that until recently, I sort of failed to understand. And most importantly it was an opportunity to drive really, really hard. Charging Through Texas Unless you've driven across it, it's hard to understand the massive space that is Texas. In places, scanning 360 degrees of horizon reveals absolutely nothing. Nothing. On its own, driving from Dallas to El Paso covers some 630 miles. Veer south to Fort Davis and you'll add another 70 onto that, not including the 75-mile Davis Mountain Scenic Loop where I found bliss behind the wheel of this insanely powerful sedan. I always expected to like the Charger Hellcat – comfortable seating for four (five in a pinch), equipped with the latest tech, wrapped in a stylish yet muscular body, like a quarterback in a tux. And it moves. The supercharged 6.2-liter Hellcat V8 pumps out 707 horsepower and 650 pound-feet of torque, which makes for one quick sedan, especially considering its heft.