1992 Dodge Ram 12 Valve Cummins Diesel 5-speed Manual Dovetail Car Hauler Mopar! on 2040-cars

Auto blog

Dodge Challenger Shakedown: '71 body, new guts

While Jeep has created a number of vintage-bodied custom vehicles with modern components, this year's SEMA show plays host to Dodge's take on the idea. The Shakedown concept began life as a 1971 Challenger and ditched almost everything in it, including the engine and chassis. What's left is a modern car with a retro look. The chassis was a particularly complicated part of the job, since the Challenger was originally a unibody car. However, Dodge chose to separate the Challenger's iconic body from its structural parts, and moved it onto a custom, one-off chassis from which the body can be removed as needed. The chassis also carries lowered suspension, Challenger Hellcat brakes, and a 6.4-liter 392 Hemi V8 connected to a six-speed manual transmission from the Viper. Dodge also installed the engine using the new Hemi engine swap kit from Mopar. With the shaker cold-air intake and custom exhaust, the Shakedown's powerplant makes 485 horsepower. View 13 Photos The body itself received plenty of tweaking as well. Dodge shaved off the drip rails, door handles, and turn signals for a cleaner look, and also fitted the grille, headlights, and taillights from a 2017 Challenger. The whole thing is finished in matte black paint with a "vibrating" stripe offset on the left side. The Shakedown also gets 20-inch Slingshot rear wheels and a pair of custom 19-inch versions for the front. On each fender is a bright red "392" decal that uses the same font as the labels on classic Mopars 360 cubic-inch V8s. Inside, the Shakedown gets the same radical upgrade as the chassis. Two Viper seats accompany a Viper steering wheel, and the rear seats are gone altogether. The Viper gearbox is shifted with a Challenger Hellcat gear knob, and carbon-fiber accents and leather adorn the wheel, door panels, instrument panel and center console. Related Video: Image Credit: FCA, Joel Stocksdale SEMA Show Dodge Coupe Concept Cars Performance

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

SRT reveals Satin Vapor Edition 300, Charger and Challenger SRT models

With the exception of some notable truck and van introductions, Chrysler brands have tended to use the Chicago Auto Show to bring out new special editions, pimp their aftermarket parts support or indulge in the occasional flight of fancy. That plan is holding true for 2014, as well. Cases in point are these new Satin Vapor Editions of the 2014-model-year Dodge Challenger, Dodge Charger and Chrysler 300 - all from SRT.
The Satin Vapor name may sound like a failed 1970s glam-rock band, or a pseudo-gynecological diagnosis from the Old West, but is, in fact, pretty much a tape-and-trim package for this trio of hi-po Mopars. 300, Challenger and Charger alike come shod with 20-inch aluminum wheels finished in Black Satin Vapor Chrome, and are accented with Satin Black bits aplenty. The 300 gets blacked-out mirrors, spoiler and roof; the Challenger applies it to mirrors and its fuel door; while the Charger has the stuff covering its roof, hood and Super Bee tail graphic.
Interiors of the cars have been mildly updated as well, with all three getting some combination of Nappa leather, ultra-suede and carbon-fiberish finishes.