5.9l Diesel 4x4 Lone Star Manual Transmission Grill Guard Gooseneck Chrome Wheel on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Dart pushed toward the grave with simplified lineup

FCA announced a while back that the Dodge Dart and its Chrysler 200 half-sibling are on the way out due to lack of interest. The 2016 model year will be the Dart's last, and Dodge has just reconfigured the lineup mid-year to lower (relative) pricing and streamline ordering. Streamlined is a nice way of saying there will be fewer choices, with three models (down from five) and limited customization beyond choosing the paint color. The odd thing is that the Dart continues to offer three different engines. And while the prices of the individual models have decreased, the former SE base trim is now gone. That means an early-2016 Dart was available for as little as $17,990, while the late-2016 Dart starts at $18,990. For that sum you get the new base model, the SXT Sport, which replaces the SXT and comes with the 2.0-liter Tigershark four-cylinder (160 horsepower, 148 lb-ft of torque) and a six-speed manual; a six-speed automatic is an available option. Standard equipment includes normal entry-level car stuff, black cloth upholstery, 16-inch wheels, and grille shutters that help improve fuel economy. The SXT Sport can be dressed up with one of three different appearance packages; Chrome adds bright accents to parts including the grille and door handles, Rallye has a black grille and a touring suspension, and the Blacktop package makes pretty much everything on the exterior black and includes a sport-tuned suspension. All three packages come with bigger wheels, too. From there it's on to the new Dart Turbo, for $20,490. It comes with the 1.4-liter turbo four (160 hp, 184 lb-ft of torque) and comes exclusively with a six-speed manual transmission. This is supposed to be the model for enthusiasts, which is how Dodge is selling the switch to manual-only. Ditching the disliked dual-clutch automatic that was previously offered with this engine doesn't hurt. This engine was also used in the former Aero model, as it's the most fuel-efficient in the lineup. The Turbo gets the Rallye appearance stuff and a different hood. At the top is the Dart GT Sport, starting at $21,900. It has the 184-hp, 2.4-liter Tigershark four-cylinder and a choice of six-speed manual or automatic transmission. This is the one with features, including a power driver's seat, the 8.4-inch Uconnect infotainment unit, digital reconfigurable gauges, dual-zone auto climate, keyless start, and a rearview camera. The latter-part-of-2016 Dart will be available in eight colors.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.