2001 Dodge Ram 4 X 4 - 2500 Base Standard Cab Pickup 2-door 5.9l on 2040-cars

Auto blog

The Dodge Demon was developed under a cloud of smoke

The Dodge Demon needs no introduction. The car is so full of superlatives that most of it sounds unbelievable until you see and hear it in action. The car was revealed after months of teasers and cryptic messages, but the public weren't the only ones in the dark. From the start, the Demon's development was a closely guarded secret. There were even some within SRT that didn't know about the project. The people behind the car went through a lot of effort to keep it that way. At an event covering the finer details of the Demon's supercharged 6.2-liter V8, Dodge CEO Tim Kuniskis and SRT Powertrain Director Chris Cowland spoke about the smoke and mirrors used to hide the Demon's development. Work on the car progressed for nearly two years before it was made public, with just a small team having full access to the project. Numbers were altered. Secret meetings were held. SRT engineers worked nights and weekends while parts suppliers were given as little information as possible to move progress forward. Preliminary work on the Demon began in April of 2015, not long after the standard Hellcat hit the streets. The goal wasn't to create a faster Hellcat. Kuniskis said that would have been easy. They wanted a single-minded vehicle that could also be driven on the road. It's the same mindset that brought about the Dodge Viper ACR. Dodge wanted a car that could sell the brand to both enthusiasts and non-enthusiasts alike. 840 horsepower is going to raise anyone's eyebrows, including the Camry owner parked down the street. While preliminary work started in April, the final greenlight wasn't given until September. The project was originally going to revive the American Drag Racer, or ADR, name. When we saw the first hints of the Demon last fall, we labeled the spy photo above the Dodge Challenger ADR. It was set to have 10-percent more power and 20-percent more launch force than the already gut-punching Hellcat. It was also only going to have a quarter-mile time in the 10s, just slightly quicker than the Hellcat. Somewhere along the line, the team realized that the ADR wasn't enough. It was just going to be a Hellcat plus, and that wasn't exciting. The main goal was changed: 9s with light. Translated, that means a 9-second quarter mile with light under the tires (read: a wheelie). From that point forward, everything about the Demon's development, from power to suspension to weight, would be done in pursuit of that goal.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2 men die in Dodge Challenger Hellcat crash at Colorado airport

Two friends died in the crash of a Dodge Challenger Hellcat over the weekend after they shot off the end of an airport runway, authorities said. That someone died in a 707-horsepower Hellcat is, sadly, not unexpected. But two aspects of the story are remarkable. First, the men's ages: The Denver Post reports the crash victims were Lynd Fitzgerald, 71, of Colorado Springs, and his passenger, Roger Lichtenberger, 76, of San Marcos, Calif. Second, their speed: The car was likely moving at over 100 miles per hour, authorities said. The men had permission to use the 8,300-foot runway at Central Colorado Regional Airport in Buena Vista. That's more than a mile and a half long. But when the car left the runway, it went 300 feet before flying over a ravine, hitting the ground, becoming airborne again, flipping end over end across a second ravine, and ultimately landing on its wheels 650 feet past the end of the pavement. Responding police officers tried to provide first aid, but the men were declared dead at the scene. "They were just test-driving this car. They went a little too fast. I don't want to surmise. ... They probably got to the end of the runway and, at that speed, didn't realize they were there so fast. And they lost control. It was just too high a speed and they got to the end of the runway," said Chaffee County Sheriff John Spezze. There were skid marks near the end of the runway, but the sheriff didn't know the length. "I've never seen anything like it," Spezze told the newspaper. "They had permission to be there. There were no laws broken." Related Video: