Manual 4.7l 4x4 Tires - Front All-season Tires - Rear All-season Power Steering on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Widebody Challenger Hellcat spotted with no camouflage

Well this is a mightily mysterious muscle car. One of our photographers caught this Dodge Challenger out testing without any camouflage. At first glance it looks like an SRT Demon, since it has the same widebody flares and front spoiler of the hellacious Challenger. However, the hood is from a garden-variety Hellcat (as if such a thing existed...), the rear spoiler has an SRT Hellcat badge, and the wheels don't come from the kitty or the Hellspawn. We have two theories as to what this SRT mishmash may be. Our first is that this is perhaps a next-generation Hellcat that takes advantage of some of the Demon's developments. It could have a more potent engine under the hood, perhaps with the extra fuel pumps and air-conditioned intercooler, along with the Demon's beefier driveline. It would be a way to keep the Hellcat relevant, and a way for people who might miss out on the one-year-only Demon to get the next closest thing. Our other theory is that this is an all-wheel-drive Hellcat. The wide fender flares and chin spoiler appeared on an all-wheel-drive Challenger concept before they made their way to the Demon. And with the introduction of the Grand Cherokee Trackhawk, we know that Mopar has an all-wheel-drive system that can handle the grunt of the 707-horsepower Hellcat mill. If an all-wheel-drive Hellcat is in the cards, it would be another way to keep the Hellcat line fresh without too much investment, and would be a treat for fans of the old all-wheel-drive concept. It would also probably be a great seller here in snowy Michigan. Oh, and it would certainly post some amazing 0-30 acceleration times. Related Video:

FCA, Ford idle plants due to semiconductor shortage

DETROIT (Reuters) - Ford and FCA will become the latest automakers to idle production facilities due to a semiconductor shortage. Ford's Louisville Assembly Plant in Kentucky will idle for a week, borrowing a down period from later in the year to compensate. Per Automotive News, FCA is idling its Brampton facility in Ontario, Canada, and one other site which has not yet been identified.  Louisville Assembly is the production site for the Ford Escape and Lincoln Corsair SUVs; Brampton Assembly produces the Chrysler 300, Dodge Charger and Dodge Challenger for FCA.  A Ford spokeswoman, who declined to identify the semiconductor supplier, confirmed the temporary shutdown to Reuters. In this, FCA and Ford join Nissan and potentially Honda in idling production in the wake of the shortage, which also hit Volkswagen late last year. The shortages are being blamed on consumer demand for silicon after production slowdowns resulting from the coronavirus pandemic. Volkswagen said it had to adjust production schedules in China, Europe and North America to compensate.  Nissan said it planned to reduce production of the Note, a hybrid electric car, at its Oppama Plant in Kanagawa prefecture, Japan, but did not give details of the scale of the output cut. The Nikkei newspaper reported that Nissan would slash its Note production at Oppama to about 5,000 units in January, from an initially planned 15,000 units. "A global shortage of semiconductors has affected parts procurement in the auto sector. As a result of this shortage, the Oppama Plant in Japan will adjust production in January, reducing production of the Nissan NOTE," Nissan said in a statement. (This article contains reporting from Reuters.)     Auto News Plants/Manufacturing UAW/Unions Chrysler Dodge Ford