2005 Srt 10 Ram 6 Speed Hurst Modifications Low Miles Viper Muscle Truck on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

2015 Dodge Challenger SRT Hellcat revving is sonic bacon

This is the Dodge Challenger SRT Hellcat, and we're sure that by now, you know its stats, including over 600 horsepower from its 6.2-liter, supercharged V8. What, pray tell, does that blown engine sound like, though?
At least judging on the sonic strength of this video, it's very, very dirty. Honestly, it sounds unlike anything that's come out of the Chrysler Group in a long time, if ever. It's loud, almost brutally so, with a bark that few road-going V8s can match.
Of course, you should be the final judge here. Take a look and a listen at the two videos below, one of which comes from our friends at Cars.com that provides a nice look under the hood, and then let us know what you think of the Hellcat's singing voice in Comments.

Dodge Viper recall requires small-handed mechanics

It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.