1969 Dodge Power Wagon Custom on 2040-cars

Auto blog

Dodge engineers trying to shoehorn Pentastar into Dart?

The fact that the Dart's launch has been a pretty dismal affair isn't what we'd call secret. Judging by its mounting inventories and poor critical reception, Dodge's successor to its unloved Caliber has struggled since it hit the market. And while both of those are difficult problems to address, at least their cause is well known - the powertrain.
Even Fiat-Chrysler CEO Sergio Marchionne has acknowledged that the powertrain options in the Dart are substandard, admitting at January's Detroit Auto Show that the powertrains are "less than ideal." Leading with the 1.4-liter turbocharged four-cylinder found in the Fiat 500 Abarth left a bad taste in the mouths of consumers thanks to the laggy engine and dead throttle response (to say nothing of the manual and dual-clutch gearboxes that needed more refinement). The addition of the 184-horsepower 2.4-liter Tigershark in the Dart GT has helped matters some, but apparently Auburn Hills doesn't think it's quite enough.
If rumors are to be believed - get that salt ready - a possible solution may be in the works. A report from Allpar is claiming that Dodge is considering fitting a Pentastar V6 into the Dart's engine bay. As the Mopar-obsessed website points out, the critically acclaimed Pentastar is available in three different sizes - 3.0 liters, 3.2 liters and the original 3.6 liters. We don't get the 3.0 here in the US, but the 3.2 can be found in the new Jeep Cherokee and the 3.6 has been seemingly fitted to every model Chrysler can shoehorn it into.

Takata airbag recall claims 209k Chrysler, Dodge vehicles

Chrysler is expanding the scope of its front passenger side Takata airbag inflator recall yet again to include 139,115 additional vehicles for a total of 208,783 units now needing these parts replaced. The latest campaign affects the passenger side inflators of the 2003-2005 Dodge Ram 1500, 2003-2005 Dodge Ram 2500, 2003-2005 Dodge Ram 3500, 2004-2005 Durango; 2005 Dakota pickup; 2005 Dodge Magnum and 2005 Chrysler 300 (pictured above), 300C and SRT8. It's limited to vehicles purchased or ever registered in Alabama, Florida, Georgia, Hawaii, Louisiana, Mississippi, Texas and the territories of American Samoa, Guam, Puerto Rico, Saipan and the US Virgin Islands. The company expects owners to be notified by February 8. The automaker just expanded the replacement campaign last week to include passenger side inflators in 149,150 pickups from the 2003 model year. However, the parts are not the same. Chrysler says this recall is for the PSPI family of components versus SPI for the last one. The company is also not aware of any injuries or accidents in its vehicles from these potentially faulty inflators, and lab testing of 600 of them finds no issues. Despite this, Chrysler is repairing these models at the request of the National Highway Traffic Safety Administration. Scroll down to read the company's full announcement of the initiative. Statement: Air-bag Inflator (Regional Field Action Expansion) December 12, 2014 , Auburn Hills, Mich. - Chrysler Group is expanding an ongoing regional field action with a recall to replace front passenger-side air-bag inflators in an estimated 208,783 older-model vehicles originally purchased or ever registered in seven U.S. states and five territories. The vehicles are equipped with front passenger-side air-bag inflators from a product family code-named "PSPI." Chrysler Group is unaware of any injuries or accidents involving PSPI inflators of the type covered by this campaign, nor has a Chrysler Group investigation identified a defect in these components. Further, laboratory tests on nearly 600 such inflators did not result in any failures. The inflators affected by this campaign differ in design and construction from PSPI inflators used by other auto makers. They also benefited from a more robust manufacturing process. However, at the request of the National Highway Traffic Safety Administration (NHTSA), Chrysler Group is expanding its replacement action beyond its original scope of Florida, Hawaii, Puerto Rico and the U.S.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.