1966 Dodge D100 Truck N/r on 2040-cars
Junction City, Kansas, United States
Body Type:PICK UP
Engine:SLANT SIX
Vehicle Title:Clear
Fuel Type:Gasoline
For Sale By:Private Seller
Interior Color: Red
Make: Dodge
Number of Cylinders: 6
Model: Power Wagon
Trim: BASIC
Cab Type (For Trucks Only): SINGLE
Drive Type: REAR
Mileage: 0
Sub Model: D100
Exterior Color: GREY
Dodge Power Wagon for Sale
Dodge carryall: legacy power wagon conversion(US $169,950.00)
1965 dodge power wagon shortbed stepside
2010 dodge ram 2500 4wd 4dr powerwagon 20"(US $27,900.00)
1972 dodge power wagon truck
Rare 1978 dodge diesel powerwagon 4x4 factory diesel at/ac/pdb one owner strong(US $5,000.00)
1978 dodge macho powerwagon 400 big block 4 speed, factory sun roof long bed
Auto Services in Kansas
Topeka Transmission Service ★★★★★
Tomco Transmission Service ★★★★★
T & N Auto Repair ★★★★★
Scholfield Auto Plaza ★★★★★
Randy Reed Buick GMC ★★★★★
Premier Auto Sales ★★★★★
Auto blog
Chrysler Recalls Over 566,000 Trucks, SUVs
Wed, Oct 29 2014Fiat Chrysler is recalling more than 566,000 trucks and SUVs in two recalls for malfunctioning fuel heaters that can cause fires and a software glitch can disable the electronic stability control. The recalls bring the newly merged company's total for the year to 6.4 million vehicles worldwide and 5.1 million in the U.S. as it continues to struggle with reliability problems. It was not immediately clear whether those totals were annual records. On Tuesday, its longtime quality chief abruptly left after Fiat Chrysler performed poorly in Consumer Reports magazine's annual reliability rankings. The largest of two recalls announced Wednesday covers almost 382,000 Ram 2500 and 3500 pickups and Ram 4500 and 5500 chassis cabs from 2010 through 2014. In trucks with 6.7-Liter Cummins diesel engines, corrosion on a fuel heater terminal could cause overheating, fuel leaks and fires. Chrysler is not aware of any fires or injuries. Owners could be warned by an odor of diesel fuel. Customers will be notified by letters starting in December. Dealers will install upgraded terminals and fuel heater housings could be replaced. The second recall covers more than 184,000 Jeep Grand Cherokee and Dodge Durango SUVs from 2014. A debris cover over a circuit board in the steering column control module can disrupt communications and disable the stability control. The problem was discovered when dealers started getting reports from customers that electronic stability control warning lights were coming on. Fiat Chrysler says it knows of no crashes or injuries caused by the problem. Technicians will upgrade software to fix the SUVs, and customers will be notified in December. Fiat Chrysler has issued 33 global recalls and 27 in the U.S. so far this year. Doug Betts, its longtime quality chief, left the company to pursue other options after Consumer Reports' survey-based rankings this year showed four FiatChrysler brands at the bottom of its list. Dodge, Ram, Jeep and Fiat performed worst of 28 brands ranked by the magazine. Company spokesman Eric Mayne said Fiat Chrysler's recalls average fewer than 200,000 vehicles each, below the industry average of 301,000. That means the company is responding quickly to problems, he said, adding that eight of its 27 U.S. recalls were announced before the company received any consumer complaints. Chrysler is not alone with a high number of recalls so far this year.
Dodge Demon makes so much torque, it needs stronger driveline parts
Thu, Mar 2 2017Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat
Junkyard 1983 Dodge Rampage has Franco-American roots
Mon, Jun 20 2016Lee Iacocca and the K-Cars get most of the credit for saving Chrysler after the company's 1979 bailout by the US government, but the success of the Simca-derived Omnirizon platform was a large, if overlooked, component of Chrysler's early-1980s resurgence. The Dodge Omni and Plymouth Horizon were sold in the United States for the 1978 through 1990 model years, and variants included the 1983-1987 Dodge Charger and the Rampage, this well-worn example of which I spotted in a Denver self-service wrecking yard last week. The early Omnirizons came with a Volkswagen-sourced 1.7-liter engine, but all of the Rampage pickups (and their near-identical Plymouth Scamp siblings) came from the factory with a 2.2-liter K-Car engine making 96 horses. This truck has a 4-speed manual transmission, which would have made it reasonably quick by Malaise Era standards. This one had plenty of body filler and rust, even before the crash that sent it on that final tow-truck ride to this place, so it wouldn't have been worth restoring. Still, we can hope that some of its parts will live on in other L-body trucks. Related Video: Featured Gallery Junked 1983 Dodge Rampage in Denver View 16 Photos Chrysler Dodge Automotive History Truck Classics dodge rampage























