2014 Dodge Journey Se on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Dodge Grand Caravan to live in fleets through 2017

After a hard-working career of hauling around families for decades, the Dodge Grand Caravan name was set to retire in 2016 under FCA's five-year plan for the US. The decision would have put all of the automaker's focus behind the next-generation Chrysler Town & Country, but that original strategy might have changed. Now, Dodge's minivan may have to work just a few more years before it can finally shuffle off. There are set to be 2016 and 2017 model year examples of the current Grand Caravan, according to an internal FCA production document obtained by Automotive News. This report suggests no changes in the minivan between those two years, and there's no mention of the company's intentions deeper into the future. "While we've announced the Grand Caravan will eventually be the minivan that goes away, we're not going into more detail at this time," a Dodge spokesperson said to AN. For the next Town & Country, production would start in Windsor, Ontario, in late February 2016. This document also suggests a brief run of 2016 Chrysler minivans based on the current model from August 2015 until February 2016. Automotive News speculates that the reprieve for the Grand Caravan could allow that model to focus on fleets and the Canadian market while the new Town and Country gets up and running. The latest generation T&C will reportedly debut at the 2016 Detroit Auto Show and will possibly carry a higher price to befit a vehicle with a more modern platform and improved tech.

Chrysler almost smothered the Hellcat before it lived

Chrysler's 6.2-liter supercharged Hellcat V8 was an absolute sensation from the very moment it was announced, and honestly, how could it not have been? Packing 707 horsepower and 650 pound-feet of torque, its numbers immediately put every other production muscle car (and many supercars) to shame. Plus, we soon learned that would be wrapped in a package retailing for around $60,000 - a pittance compared to other vehicles offering similar grunt. However, the Hellcat almost never got the chance to rumble under the hood of the Challenger and Charger.
The Hellcat was initially proposed back in 2011, back when Fiat was deciding its future strategy for Chrysler Group, according to Automotive News. At the time, the company was just emerging from its bankruptcy doldrums, and an ultra-high-performance V8 wasn't exactly a must-have item. The program didn't move forward. However, SRT engineers kept fighting, according to AN, and four months later, they received the green light to pull the project off the shelf and continue developing the Hellcat. The muscle car world is certainly better for that decision.
The work of those engineers focused on taking Chrysler's standard 6.2-liter V8 and making it reliably handle all of the extra power from the supercharger. "It came down to micron levels of changes in the crank to be able to withstand the pressures of the engine," said Chris Cowland, director of advanced and SRT powertrain, to Automotive News. The changes amounted to switching out about 91 percent of the parts to make the Hellcat, including some quite minuscule alterations. For example, the washer holding the supercharger pulley is embedded with industrial diamonds to keep it from slipping.