2006 Dodge Grand Caravan Se Dvd Player Stow N Go Clean Carfax 1 Own No Reserve on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2013-14 Dodge Viper recalled over faulty door handles

The 2013-14 Dodge Viper is getting a voluntary recall affecting 1,762 cars worldwide to replace their door-handle assemblies. Of the affected vehicles, FCA US reports there are 1,451 in the US, 160 in Canada, 17 in Mexico and 59 of them outside of NAFTA. After receiving three reports of doors either not closing or opening while driving a low speeds, FCA US engineers found a new sealant from a supplier didn't provide sufficient moisture protection to the electronic switches for the door latches. If the parts get wet, this can potentially cause a short circuit. The automaker is quite clear that are no reports of accidents of injuries from this problem. As always, the recall repairs will be done at no cost to owners, and FCA US will be getting in touch with customers soon about the problem. Related Video: Statement: Door-handle Assemblies April 9, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 1,762 cars globally to replace their door-handle assemblies. FCA US launched an investigation after the Company received three warranty claims linked to doors that failed to close or opened inadvertently while vehicles were moving at low speed. The Company is unaware of any related injuries or accidents. Engineers determined a sealant, newly adopted by a supplier, provided inconsistent moisture protection to the electronic switches that control the door latches. Switches exposed to moisture may short-circuit. Affected are approximately 1,451 model-year 2013-14 Dodge Viper SRT cars in the U.S.; 160 in Canada; 17 in Mexico and 59 outside the NAFTA region. Affected customers will be notified and advised when they may schedule service, which will be performed at no cost. Customers with questions may call the FCA US Customer Information Center at 1-800-853-1403.

Indications of 825 hp and emissions issues for Hellcat called 'speculation' by Chrysler

The 2015 Dodge Challenger SRT Hellcat is probably one of the hottest cars of the moment mostly because of its insane, 707-horsepower supercharged V8. However, there are conflicting reports coming out that the powerplant might be having problems with its emissions compliance and may be capable of even more power.
Jalopnik says that an unnamed source within Fiat Chrysler Automobiles told it that the Hellcat was having problems meeting emissions standards at its 707-horsepower tune. The person claimed that the automaker has been testing the V8 with different types of sensors, possibly to make it a bit cleaner in the future. Autoblog spoke to SRT spokesperson Dan Reid, and he said about the claimed poor emissions, "It's totally speculation."
The source also claimed that the Hellcat had been dynoed at a monumental 825 horsepower, internally. Based on the other rumor, though, it's hard to imagine the engine being emissions compliant like that. Autoblog also asked Reid about this speculation about more power and was told, "They are totally speculating about that."