Alloy Wheels Back Up Camera Spoiler 3rd Row Seat Parking Aid Off Lease Only on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Stellantis aims to eliminate separate inverter, charger to improve EV efficiency

Stellantis has announced that, in collaboration with French battery company Saft and French National Center for Scientific Research, has made significant progress in eliminating two major components of an electric vehicle powertrain: the on-board charger and the power inverter for the motor. The company claims that doing this will allow for better space use in vehicles, as well as improvements in efficiency, cost and reliability of components. As a quick primer, also explained in the below video, the on-board charger and power inverter are sort of translators to get the right current to different parts of the electric powertrain. The on-board charger takes AC power from the grid and converts it to DC to charge the batteries. Then when power goes from the batteries to the electric motor, the power inverter converts that DC power back to AC. These components aren't exactly small. Frequently you'll find them packaged somewhere under the hood. What Stellantis and its cohorts have developed, and have been using on a test vehicle since last summer, are small power inverter boards that can be mounted very closely to the battery packs. They can handle both conversion needs, for charging and discharging, instead of needing two separate devices. The most obvious perk to this is that you can do away with those traditional components and free up more space, either for making smaller vehicles without losing interior volume, or adding space to a vehicle that wouldn't have had it otherwise. There's the additional benefit of reduced weight, something that EVs struggle with. Stellantis also claims improvements in efficiency, reliability, and cost, however, it didn't go into detail as to how this setup would do that exactly. We'll try to get in touch with representatives from Stellantis in order to get more information. We're still a ways out from seeing this technology in production Stellantis vehicles. The company said it aims to apply it to vehicles by the end of the decade. Saft is also looking at using it on stationary battery systems as well. So maybe we'll see it on a 2029 Ram 1500 REV, but for now, we'll be living with traditional chargers and inverters. Related Video: Green Alfa Romeo Chrysler Dodge Fiat RAM Technology Electric