New 2013 Dodge Dart Se - Fuel Saver - Auto on 2040-cars

Auto blog

All hail the Hellephant, Mopar's 1,000-horsepower crate engine

It's shocking to say this, but the all-powerful Dodge Demon looks weak now that Mopar has unleashed the Hellephant. This crate motor makes 1,000 horsepower and 950 pound-feet of torque, and its name is a combination of the nickname for the old 426-cubic-inch Hemi V8 and, obviously, the Hellcat. This monster is a 426-cubic-inch version of the current third-generation Hemi V8 topped by a supercharger similar to what the Hellcat line packs. Everything is cranked up to — or perhaps, past — 11. The engine block is made of aluminum and weighs 100 pounds less than the equivalent iron block. All of the internals are forged. The stroke and bore have been increased. The supercharger produces 15 pounds of boost and displaces 3 liters; more than the 2.7-liter blower on the Demon and the 2.4-liter blower on the Hellcat. And as big and powerful as it is, it will still rev to 7,000 rpm. It's a thoroughly monstrous motor, but shockingly, it won't be that difficult to live with. For one thing, Mopar will offer a complete kit to get the engine up and running, including an engine computer, wiring harness and drive-by-wire throttle. It also runs on 93-octane pump gas. That's especially amazing considering the Demon engine "only" makes 840 horsepower, and that's on race gas with 100+ octane fuel. It also has us wondering what the Hellephant could make on racing fuel. The Mopar folks did say that there's room to add more power. Pricing wasn't announced for the Hellephant engine. The Hellcat crate engine retails at $19,350 directly from Mopar, so it's safe to assume that the Hellephant will go for more. The installation kit with the computer and harness will be an extra charge of likely over $2,000, based on the Hellcat kit. The engine and the kit will be available in the first quarter of 2019. Related Video: Featured Gallery Hellephant Crate Engine SEMA Show Chrysler Dodge Jeep RAM Performance dodge demon hellephant

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Aficionauto drives Vin Diesel's fast and furious 1970 Dodge Charger

The Aficionauto host Christopher Rutkowski has a real passion for original and replica cars from movies and television, whether they are from James Bond, Jurassic Park, or incredibly obscure Japanese shows. However, he might have outdone himself this time because he hopped into one of the biggest automotive stars of contemporary cinema. This 1970 Dodge Charger appeared in Fast & Furious and came back in Fast Five, where Paul Walker actually drove it. The menacing, black muscle car will make its return to the franchise in the seventh film, too.
The Fast and Furious Charger is a real beast no matter how you look at it. The interior is nothing more than two seats and a roll cage, and as the video shows, this thing vibrates constantly like a coiled mass of muscle ready to strike. The camera can barely stay in place most of the time. Also, Dom's Dodge is more than happy to do a smoky burnout and leave the driver partially deaf afterward from its wonderful, ear-splitting engine roar.
The Aficionauto also interviews the man who controls the keys to this beast. Bob Hartwig was once an F-15 pilot, but he also loved Hollywood vehicles. Now, he's a partner at Picture Car Warehouse, a company with about 850 cars that supplies vehicles to film studios. This Charger definitely seems to be Hartwig's favorite in the collection, as it should be.