2013 Dodge Dart on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Will the Dodge Demon do a 10-second quarter-mile?

The final teaser for the Dodge Demon is finally here, and it might just give us a clue as to how quick the new car really is. A brief glimpse at a time slip shows what might be a 10-second quarter-mile time. That's a significant step up from the standard Hellcat's 11.7 seconds, but considering all of the Demon's modifications, it's not an unreasonable time. The new video, "Judgment Day," shows the new Demon in its natural habitat, a quarter-mile drag strip. There isn't much new information, aside from the brief glimpse at a time slip. There is a good shot of the car in action and some nice audio from what we assume is a supercharged 6.2-liter Hemi. For comparison, the new 2016 Chevrolet COPO Camaro is capable of a 10.7-second quarter-mile run, while the 2016 Ford Mustang Cobra Jet dips all the way down into the 8s. The full reveal is less than a week away. Look for more information, including the long-awaited horsepower rating, next week during our coverage of the 2017 New York Auto Show. Related Video: New York Auto Show Dodge Coupe Performance dodge demon dodge hellcat