1974 Dodge Dart Swinger Hardtop 2-door 3.7l on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2019 Dodge Challenger R/T Scat Pack Widebody Drivers' Notes | Widebody for everybody

The 2019 and soon to be 2020 Dodge Challenger R/T Scat Pack Widebody is another Challenger dart thrown against the wall by Dodge. It takes the desirable Widebody package we’ve seen on Hellcats and applies it to the naturally aspirated Scat Pack with the 6.4-liter V8. This kit includes stiffer adaptive shocks, stiffer springs, larger stabilizer bars, big Brembo brakes, a 3.09 rear axle ratio, 20-inch forged wheels and massive 305 section-width tires on all four corners. Most important of all, you get the special Widebody fender flares that give the car its signature look. The package is $6,000 on top of a regular Scat Pack. That means the cheapest youÂ’ll step into a Scat Pack Widebody is $46,740. The Widebody that rolled through our offices came in at a much-higher $57,295 after a number of options were tacked on. Many of these, you can skip. The 485 horsepower and 475 pound-feet of torque that comes standard is the most important aspect of this big coupe. Several packages costing more than $1,000 each add convenience and driver assistance tech, and the Harman/Kardon system is a hefty $1,595. With such a loud engine and exhaust, itÂ’s hardly worthwhile. Our tester also had the $1,595 eight-speed automatic transmission. ThisÂ’ll let you scare unsuspecting bystanders with the remote start system, but opting for a manual is an easy way to save some cash and increase driver involvement. With all the modern technology like adaptive cruise control, auto high-beams, heated and cooled seats, and blind-spot detection, the Challenger tries its best to keep up with the times. ItÂ’s no technological marvel, but itÂ’s neat to see some of these options available for folks who might want them. Still, tech gizmos are not what the Widebody is about. This Challenger keeps the same personality as all of those before it, but adds a dash of handling and hostility to its outward appearance. Here are our varied experiences with it during a week of testing. Editor-in-Chief, Greg Migliore: Yes, you can put a rear-facing convertible car seat in a Dodge Challenger. I did. It actually wasnÂ’t that hard. Remember, the Challenger is genetically a Mercedes sedan and shares underpinnings with the Dodge Charger. The biggest hurdles are ingress and egress, which is to be expected in any coupe. The roofline is low, but really not that bad. I simply lifted my toddler and maneuvered him into the backseat.  I was able to get him secured and fastened, and then I just stepped out of the car.

Lee Iacocca's very first Dodge Viper RT/10 nets $285,500 at auction

The first 1992 Dodge Viper RT/10 to roll down the assembly line, which was snapped up by Chrysler chief Lee Iacocca, yesterday hammered at the Bonhams auction in Arizona for $285,500, more than double the pre-sale estimate. According to a history of the car published by the auction house, Iacocca, in his introduction of the Viper to the press, pointed to the car on stage and said, "This one right here is mine." That historic Viper, with serial number 001, has never been available on the open market, as Iacocca kept the car from new until he passed away last year. The car has been driven just 6,200 miles and was being sold by his estate. Other Lee Iacocca cars offered at the same sale fared less well. A 1986 Chrysler LeBaron Town & Country convertible — the ultimate expression of Iacocca's company-saving K-cars — with 20,500 miles on it sold for $19,040. That's less than the $20,000 to $25,000 the auction house had estimated the car would bring. A third car from the former auto executive's estate was a customized 2009 Ford Mustang. The pony car was one of a limited run of 45 Iacocca-branded custom Mustangs, which were reworked by Metalcrafters and sold by Galpin Ford in Los Angeles. The Iacocca Mustang, never titled and with 220 miles on it, hammered for $49,280. Related Video:     Featured Gallery Lee Iacocca's 1992 Dodge Viper RT/10 View 13 Photos Celebrities Chrysler Dodge Auctions Automotive History