on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Pontiac Aztek enjoys rebirth thanks to Millennials

Apparently, Millennials – those between 18 and 34 – aren't afraid to look different on the road, and they like performance, too. A new study by Edmunds is discovering some surprising vehicle choices by this group. Among them, the long-derided Pontiac Aztek is getting a new day in the sun with 25.5 percent its buyers coming from this generation in the first half of 2015. For comparison, Millennials represent an average of 16.8 percent of used car purchases. The Aztek is slowly shaking its reputation as a styling abomination, which seems tied to its appearance on Breaking Bad. The show premiered in 2008, and the Pontiac has been on this list for four of the past five years, according to Edmunds. It even led the pack in 2010. A recent Retro Review from MotorWeek also showed that the crossover wasn't always so hated. While it's still a shock to see the Aztek on any popularity list, the awkward-looking crossover only ranks sixth among Millennials. The vehicle with the biggest portion of buyers from the generation is the Dodge Magnum with 27.6 percent. According to Edmunds, the bluntly styled wagon is especially popular in Detroit and Chicago. The Chrysler Pacifica comes in a close second at 27.3 percent. When it comes to used cars, value and utility appear to trump just about anything else for many Millennial buyers," Edmunds analyst Jeremy Acevedo said in the report. Young buyers aren't afraid of sporty rides, either. The Subaru WRX has 26.4 percent Millennial buyers to rank third place on the list, and the Volkswagen R32 takes fifth at 25.7 percent. Just a few points lower in seventh place is the Nissan GT-R at 25.4 percent, and the final performance machine in 10th place is the Lexus IS-F with 24.7 percent. Related Video:

Watching a 2010 Dodge Challenger become a Plymouth GTX is a restomod education

We cover a lot of restomods, many of them one-off SEMA show cars and low-volume builds from professional shops that sell for hundreds of thousands of dollars. Autoevolution tells the story of Steve Mirabelli, who creates Mopar restomods as a hobby when home from his day job as a NASCAR Sprint Cup car builder for Hendrick Motorsports. Working on his own, the stuff we've seen from Mirabelli so far deserves to sit at the same table as Kore and Ring Brothers. First he spent four years turning a 2006 Dodge Charger SRT8 into a 1968 Dodge Charger, the cardinal feat being the proportions; many builds leave the modern Charger's thick sides uniting a nosecone and high Daytona wing. Mirabelli didn't let himself off so easy, finding a '68 Charger abandoned in a field to lay over the '06 chassis, then working the proportions — such as adding 11 inches to the wheelbase — so that the 20-inch wheels look like they could have been stock fitment in '68.    His current build is recasting a 2010 Dodge Challenger R/T into a thid-gen Plymouth GTX, May 6 representing two years since the first video documenting the process. These videos are another highlight. For anyone who's ever wanted to see every step in how the professionals turn classic cars into modern monsters, Mirabelli's criminally under-watched YouTube channel is the place to go. There are 43 videos so far on the GTX transformation, with Mirabelli taking time to explain and demonstrate his thought process and methods every step of the way. It's an online course in restomodding, maybe the perfect final binge before returning to our outdoor lives.  Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.