1969 Dodge Coronet Super Bee Clone on 2040-cars
Lincoln University, Pennsylvania, United States
|
Up for auction is a 1969 Dodge Coronet Super Bee clone. This car is a project that needs to be finished. This 1969 Dodge Coronet was dismantled and place on and rotisserie and media blasted the coated with epoxy primer and sprayed with a base coat clear coat on the uner carriage. New rear quarter, new doors, new trunk pan and rear frame rails were installed. the engine is a rebuilt Mopar 400 big block with a rebuilt 727 torque flight transmission. Car is upgraded with front wheel disk break system. Most of the parts to finish the car come with it. If you would like more information about this 69 Dodge Coronet feel free to e mail me.
|
Dodge Coronet for Sale
1967 dodge coronet red 440 automatic gorgeous
1970 dodge coronet superbee(US $41,900.00)
1957 dodge coronet 2 door, lancer, royal, mopar, belvedere, savoy
1968 dodge coronet 440 hardtop 2-door 7.2l
1970 dodge coronet super bee superbee restored numbers matching 383 ramcharger(US $35,000.00)
1966 dodge coronet 440 pro street / strip 440 big block
Auto Services in Pennsylvania
Young`s Auto Body Inc ★★★★★
West Shore Auto Care ★★★★★
Village Auto ★★★★★
Ulrich Sales & Svc ★★★★★
Trust Auto Sales ★★★★★
Steve`s Auto Body & Repair ★★★★★
Auto blog
Dodge Scat Pack for 5.7L Hemi V8 detailed, priced
Sat, 05 Apr 2014Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.
Dodge Demon makes so much torque, it needs stronger driveline parts
Thu, Mar 2 2017Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat
Dodge shows can-do attitude with grand Can'avan sculpture
Fri, 01 Nov 2013There are lots of ways to celebrate an important birthday, and all of them are well deserved. You can throw a big party, buy yourself something nice, or - if you're the altruistic type - do something for others in need. The latter is how Chrysler has opted to mark the 30th anniversary of its Dodge Grand Caravan and Chrysler Town & Country.
Together with hunger-advocacy organization Canstruction, the Chrysler Foundation has built a full-scale replica of the Grand Caravan out of 30,000 food cans in the square at the corner of Yonge and Dundas in Toronto, a ways down the highway from where the real vans are built in Windsor. The sculpture was built over the course of 10 hours by 30 volunteers and was displayed earlier this week.
Now the installation is being taken down, and the cans of food are being donated to the Daily Bread Food Bank, which will assemble them into 2,000 food baskets to be distributed to those in need through its network of 200 food banks across the Canadian metropolis. Check out a neat time-lapse video of the build and the press release below.




