1967 Dodge Coronet 440/500 R/t Clone 440ci V8 on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Watch the Dodge Charger SRT Hellcat verify its 204-mph top speed

The industry is producing some ridiculously fast four-doors these days, from the Porsche Panamera and Maserati Quattroporte to the Mercedes E63 AMG and BMW M5. But the fastest of them all doesn't cost six figures. It doesn't even come from Europe. It's made right here in North America, by a US automaker. And it starts at under $64k. We're talking about the Dodge Charger SRT Hellcat, the Pentastar muscle sedan with the 6.2-liter supercharged V8 and its 707 horsepower. Dodge claims it's the "quickest, fastest, most powerful [production] sedan ever," and they're not just blowing smoke... or smoking tires. During the final stages of development, engineers from Auburn Hills took a bone-stock, Hellcat-powered Charger out to a seven-mile oval for a top speed run and they filmed the occasion for posterity. The result? 206.9 miles per hour with the wind, 202.2 against it, for a two-way average top speed of 204.55 mph. Chew on that, imports.

The Dodge Demon was developed under a cloud of smoke

The Dodge Demon needs no introduction. The car is so full of superlatives that most of it sounds unbelievable until you see and hear it in action. The car was revealed after months of teasers and cryptic messages, but the public weren't the only ones in the dark. From the start, the Demon's development was a closely guarded secret. There were even some within SRT that didn't know about the project. The people behind the car went through a lot of effort to keep it that way. At an event covering the finer details of the Demon's supercharged 6.2-liter V8, Dodge CEO Tim Kuniskis and SRT Powertrain Director Chris Cowland spoke about the smoke and mirrors used to hide the Demon's development. Work on the car progressed for nearly two years before it was made public, with just a small team having full access to the project. Numbers were altered. Secret meetings were held. SRT engineers worked nights and weekends while parts suppliers were given as little information as possible to move progress forward. Preliminary work on the Demon began in April of 2015, not long after the standard Hellcat hit the streets. The goal wasn't to create a faster Hellcat. Kuniskis said that would have been easy. They wanted a single-minded vehicle that could also be driven on the road. It's the same mindset that brought about the Dodge Viper ACR. Dodge wanted a car that could sell the brand to both enthusiasts and non-enthusiasts alike. 840 horsepower is going to raise anyone's eyebrows, including the Camry owner parked down the street. While preliminary work started in April, the final greenlight wasn't given until September. The project was originally going to revive the American Drag Racer, or ADR, name. When we saw the first hints of the Demon last fall, we labeled the spy photo above the Dodge Challenger ADR. It was set to have 10-percent more power and 20-percent more launch force than the already gut-punching Hellcat. It was also only going to have a quarter-mile time in the 10s, just slightly quicker than the Hellcat. Somewhere along the line, the team realized that the ADR wasn't enough. It was just going to be a Hellcat plus, and that wasn't exciting. The main goal was changed: 9s with light. Translated, that means a 9-second quarter mile with light under the tires (read: a wheelie). From that point forward, everything about the Demon's development, from power to suspension to weight, would be done in pursuit of that goal.