2023 Dodge Charger on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video:

Dodge Viper recall requires small-handed mechanics

It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.