2014 Dodge Charger Sxt on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Fiat Chrysler to get $105M fine from NHTSA for recall woes

The National Highway Traffic Safety Administration is about to send a powerful message to automakers doing business in the United States, assuming reports of an upcoming $105 million fine against Fiat Chrysler Automobiles comes to fruition. In addition to the record-setting monetary fine, according to The Wall Street Journal, FCA will have to accept an independent auditor that will monitor the company's recall and safety processes and will be forced to buy back certain recalled vehicles. In other cases, such as with Jeep Grand Cherokee and Liberty models with gas tanks that could potentially catch fire in certain types of accidents, FCA will offer financial encouragement for owners to get their recall work done or to trade those older vehicles in on new cars, according to the report. FCA could reportedly reduce its fines if it meets certain conditions, though those remain unclear at this time. These actions against FCA are being taken after NHTSA began a probe into the automaker over almost two dozen separate instances where the government claims FCA failed to follow proper procedures for recalls and safety defects. Included in those safety lapses are more than 11 million vehicles currently in customer hands. These penalties and fines are separate from the investigation over security problems with Chrysler's Uconnect system that allowed hackers to obtain remote access into key vehicle systems in 1.4 million vehicles. Related Video: Image Credit: Marco Bertorello/AFP/Getty Earnings/Financials Government/Legal Recalls Chrysler Dodge Fiat Jeep RAM Safety fiat chrysler automobiles fine

Chrysler to accelerate production of 2013 Ram and V6 engines

Chrysler is adding a third shift at its Warren Truck plant to meet demand for the new 2013 Ram pickup. And with tight supplies of its Pentastar V6, the company is also boosting output at its Mack Engine plant.
The expansions will add 1,250 jobs and are part of a $238 million investment by Chrysler in the Detroit area. Warren's third shift will begin work sometime in the spring, a Chrysler rep told Automotive News. Mack's increased Pentastar production a could include both 3.6 and 3.2-liter engines.
The company says it also plans to invest $40 million in its Trenton Engine plant to allow for production of a 3.2-liter V6 as well as the Tigershark inline-four for the upcoming Jeep Liberty replacement.