We Finance!!! 2010 Dodge Challenger R/t Hemi 6 Speed Heated Seats 5k Texas Auto on 2040-cars

Auto blog

Dodge Charger Hellcat and Tesla Model S P85D in Motor Trend Head 2 Head battle

One has James Bond Mode, Insane Mode, Creep Mode, and, yes, Insane Creep Mode. The other has 707 horsepower and is a heck of a lot cheaper. But which one is the bigger American badass? We figure most people already have strong opinions on the Dodge Charger Hellcat and Tesla Model S P85D, and they aren't likely to be swayed too far in the opposite direction by another person's viewpoint. Still, we think you'll enjoy watching the video above. In it, Autoblog friend and Motor Trend "Head 2 Head" host Jonny Lieberman summons smoke, shares smiles, and spouts spiels about both cars, finally finding one just slightly more badass than the other. Which ridiculously ludicrous American sedan takes top honors? Watch above to find out. Related Gallery 2015 Dodge Charger SRT Hellcat View 142 Photos Related Gallery 2015 Tesla Model S P85D: Detroit 2015 View 18 Photos News Source: Motor Trend via YouTube Green Dodge Tesla Electric Performance Videos Sedan motor trend head 2 head dodge charger hellcat autoblog black

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

UAW workers strike at Stellantis casting plant in Indiana

DETROIT — United Auto Workers union members went on strike Saturday at the Stellantis casting plant in Indiana, citing health and safety issues including the company's alleged refusal to repair and replace the plantÂ’s air conditioning and heating systems. The 35-acre plant in Kokomo makes parts used in the powertrains of Chrysler, Dodge, Jeep and RAM vehicles and a long-term strike could affect vehicle assembly lines across North America. Stellantis says production had not been scheduled for this weekend and it hoped to resume negotiations as soon as possible on a contract with striking UAW Local 1166. In a statement, Stellantis said it was committed “to providing a safe and healthy work environment for all employees. After bargaining in good faith for two days and presenting an offer we believed addressed the unionÂ’s concerns, we are disappointed by the UAWÂ’s decision to walk out.” The 1,200-worker plant, Kokomo Casting, is the world's largest die cast facility, according to Stellantis. It makes aluminum parts for components including transmissions and engine blocks. The UAW local complained in a statement that Stellantis “claims it has no money to meet its membership's basic needs while ”making record profits and investing billions in a new battery plant across the street." UAW local president David Willis did not immediately return a phone call seeking comment. A person who answered the phone at union offices said he was preparing for a resumption in negotiations. The casting plant is to be retooled to produce engine blocks for hybrid-electric vehicles. In May, Stellantis announced a $2.5 billion joint venture with Samsung to build an electric vehicle battery factory in Kokomo that is to employ 1,400 workers. Stellantis, formed last year with the merger of Fiat Chrysler and FranceÂ’s PSA Peugeot, had said it would build two electric vehicle battery factories in North America. The other is slated for Windsor, Ontario. Plants/Manufacturing UAW/Unions Chrysler Dodge Jeep RAM