Dodge Challenger Srt8 392 on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

The Dodge Demon's massive torque wrinkles its massive tires

Horsepower doesn't mean a damn thing if a car can't properly put the power down. That's why Dodge has fitted the upcoming Demon with some of the stickiest road-legal rubber available. Those Demon-branded Nitto NT05R drag radials skirt by regulations with just the smallest of margins, and in order to maximize the potential of the 315/40R 18 size tires Dodge increased the car's torque multiplication with a higher stall speed for the torque converter and a 3.09 rear axle. The 12.6-inch-wide tires are fitted to 18x11-inch wheels at all four corners, and they're fatter than those 305-section front tires on the Camaro Z/28 that we raved about years ago. Dodge says the combination of soft, gooey rubber and the new gear ratio gives the Demon about a 15 percent larger tire contact patch, more than twice as much grip, and roughly an 18 percent increase in both converter torque and rear-axle torque multiplication. Simply put, the Dodge Demon moves. You can see the results in the teaser video above, which is titles "Multiplication" and shows the crazy wrinkling of the sidewall that results from putting that torque to the road. We wouldn't be surprised if the inner rim of the wheel needs some grip to keep the tire seated, something Chevy had to do on the last Z/28. There is something wonderful about Dodge's approach to performance cars. While the Ford Mustang and Chevrolet Camaro have moved on from their muscle car upbringings with proper track-focused models, Dodge has stayed true to its roots by developing a machine that's sole intent is traveling a quarter-mile quicker than anything else on the road. Twisty roads may be fun, but there is something wholly and deeply satisfying about going deep into the accelerator with a comical amount of power at your disposal. We can't wait. Related Video: New York Auto Show Dodge Coupe Performance dodge demon dodge hellcat dodge challenger srt demon drag strip

Final Dodge Demon and Dodge Viper to be auctioned off for charity

A little while ago we wrote about the Viper factory being recommissioned into a museum, that will hold the historic cars originally evicted from the Walter P. Chrysler museum. Now, what happened to the last Viper that factory built? It's getting auctioned off, in good company. Barrett-Jackson is auctioning the last 2017 Viper built, together with a 2018 Dodge Challenger SRT Demon said to be the last Demon produced. Crossing the block in June in Uncasville, Connecticut, the pair of cars produces a total of 1,485 horsepower, of which the Demon accounts for 840 horses and the Viper for 645. Both are finished in bright Viper Red, and yes, the Demon will include the optional passenger seat. All proceeds from the sale will go to charity, to United Way. "Pairing the last Dodge Challenger SRT Demon and the Dodge Viper production cars – two of America's most sought-after vehicles – under the roof of Barrett-Jackson gives someone the 'last' chance to own this unique piece of automotive history, and Dodge//SRT the opportunity to raise money for a cause close to our hearts", said FCA's Steve Beahm. In addition to the cars, the sale will include memorabilia and a Demon Crate, which includes narrow, drag-spec front tires, performance modules and track tools. The auction is held from June 20th to 23rd. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Image Credit: FCA Dodge Auctions Coupe Performance FCA dodge demon