72 Dodge Challenger Rallye on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

FCA adds 88k Dodge Challengers to Takata inflator recall

The Takata airbag inflator recall from FCA US is growing 88,346 vehicles larger in the US after the company's discovery of the faulty parts in the 2008-2010 Dodge Challenger. The affected examples have production dates between September 19, 2007, and October 29, 2010, and the coupes need the replacement components on the driver's side. According to chronology posted by the National Highway Traffic Safety Administration (as a PDF), the automaker was auditing the models covered under the campaign in July and "identified a population of vehicles that was inadvertently excluded." Initially, FCA believed these cars were using an unrecalled Takata inflator. The audit revealed that the affected cars indeed used a recalled version. As with the rest of the faulty parts, exposure to moisture can cause them to ignite too quickly during an airbag deployment and spray shrapnel at occupants. The problem has been linked to at least eight deaths worldwide and a vehicle fire in Japan. The Challenger wasn't previously part of FCA's 3.3-million unit national campaign or the subsequent expansion. According to FCA US the parts to complete the repairs in these Challengers aren't currently available. However, owners will be notified of the issue by mail starting August 14. They will receive a second notice when the parts become available. Related Video: RECALL Subject : Driver Side Frontal Air Bag Inflator May Rupture Report Receipt Date: JUL 10, 2015 NHTSA Campaign Number: 15V444000 Component(s): AIR BAGS Potential Number of Units Affected: 88,346 All Products Associated with this Recall Vehicle Make Model Model Year(s) DODGE CHALLENGER 2008-2010 Details Manufacturer: Chrysler (FCA US LLC) SUMMARY: Chrysler (FCA US LLC) is recalling certain model year 2008-2010 Dodge Challenger vehicles manufactured September 19, 2007, to October 29, 2010. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture. CONSEQUENCE: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death. REMEDY: Chrysler will notify owners, and dealers will replace the driver's frontal air bag inflator, free of charge. Parts to remedy the vehicles are not currently available. Interim notices will be mailed to owners beginning August 14, 2015.

A car writer's year in new vehicles [w/video]

Christmas is only a week away. The New Year is just around the corner. As 2014 draws to a close, I'm not the only one taking stock of the year that's we're almost shut of. Depending on who you are or what you do, the end of the year can bring to mind tax bills, school semesters or scheduling dental appointments. For me, for the last eight or nine years, at least a small part of this transitory time is occupied with recalling the cars I've driven over the preceding 12 months. Since I started writing about and reviewing cars in 2006, I've done an uneven job of tracking every vehicle I've been in, each year. Last year I made a resolution to be better about it, and the result is a spreadsheet with model names, dates, notes and some basic facts and figures. Armed with this basic data and a yen for year-end stories, I figured it would be interesting to parse the figures and quantify my year in cars in a way I'd never done before. The results are, well, they're a little bizarre, honestly. And I think they'll affect how I approach this gig in 2015. {C} My tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015 it'll be as high as 73. Let me give you a tiny bit of background about how automotive journalists typically get cars to test. There are basically two pools of vehicles I drive on a regular basis: media fleet vehicles and those available on "first drive" programs. The latter group is pretty self-explanatory. Journalists are gathered in one location (sometimes local, sometimes far-flung) with a new model(s), there's usually a day of driving, then we report back to you with our impressions. Media fleet vehicles are different. These are distributed to publications and individual journalists far and wide, and the test period goes from a few days to a week or more. Whereas first drives almost always result in a piece of review content, fleet loans only sometimes do. Other times they serve to give context about brands, segments, technology and the like, to editors and writers. So, adding up the loans I've had out of the press fleet and things I've driven at events, my tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015, it'll be as high as 73. At one of the buff books like Car and Driver or Motor Trend, reviewers might rotate through five cars a week, or more. I know that number sounds high, but as best I can tell, it's pretty average for the full-time professionals in this business.